It is impossible to pass Cisco ccent ccna icnd1 100 105 exam without any help in the short term. Come to Examcollection soon and find the most advanced, correct and guaranteed Cisco icnd 100 105 practice questions. You will get a surprising result by our Up to the immediate present ICND1 Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) practice guides.

P.S. Vivid 100-105 dumps are available on Google Drive, GET MORE: https://drive.google.com/open?id=1p6goOol79JPy5WQ9QjPXU5ZCXFzabnVd


New Cisco 100-105 Exam Dumps Collection (Question 10 - Question 19)

Question No: 10

Refer to the exhibit.

Which two statements are true of the interface configuration? (Choose two)

A. The encapsulation in use on this interface is PPP.

B. The default serial line encapsulation is in use on this interface.

C. The address mask of this interface is 255.255.255.0.

D. This interface is connected to a LAN.

E. The interface is not ready to forward packets.

Answer: A,C


Question No: 11

Which routing protocol has the smallest default administrative distance?

A. IBGP

B. OSPF

C. IS-IS

D. EIGRP

E. RIP

Answer: D

Explanation: http://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/15986-admin-distance.html

Default Distance Value TableThis table lists the administrative distance default values of the protocols that Cisco supports:

Route Source

Default Distance Values

Connected interface 0

Static route 1

Enhanced Interior Gateway Routing Protocol (EIGRP) summary route 5

External Border Gateway Protocol (BGP) 20

Internal EIGRP 90

IGRP 100 OSPF 110

Intermediate System-to-Intermediate System (IS-IS) 115

Routing Information Protocol (RIP) 120

Exterior Gateway Protocol (EGP) 140

On Demand Routing (ODR) 160

External EIGRP 170

Internal BGP 200

Unknown* 255


Question No: 12

Which technology allows a large number of private IP addresses to be represented by a smaller number of public IP addresses?

A. NAT

B. NTP

C. RFC 1631

D. RFC 1918

Answer: A


Question No: 13

SW-C has just been added to the network shown in the graphic

What is the purpose of assigning a default gateway to this switch?

A. allows connectivity to Router B from the switch prompt

B. allows console port connectivity to the switch from Host A

C. allows connectivity to remote network devices from Host B

D. allows the switch to pass traffic between Host A and Host B

Answer: A


Question No: 14

If NVRAM lacks boot system commands, where does the router look for the Cisco IOS by default?

A. ROM

B. RAM

C. Flash

D. bootstrap

E. startup-config

Answer: C


Question No: 15

Refer to the exhibit.

What does the address 192.168.2.167 represent?

A. the TFTP server from which the file startup-config is being transferred

B. the router from which the file startup-config is being transferred

C. the TFTP server from which the file router-confg is being transferred

D. the TFTP server to which the file router-confg is being transferred

E. the router to which the file router-confg is being transferred

F. the router to which the file startup-config is being transferred

Answer: D


Question No: 16

Based on the network shown in the graphic

Which option contains both the potential networking problem and the protocol or setting that should be used to prevent the problem?

A. routing loops, hold down timers

B. Switching loops, split horizon

C. routing loops, split horizon

D. Switching loops, VTP

E. routing loops, STP

F. Switching loops, STP

Answer: F


Question No: 17

Scenario:

You are a junior network engineer for a financial company, and the main office network is experiencing network issues. Troubleshoot the network issues.

Router R1 connects the main office to the internet, and routers R2 and R3 are internal routers.

NAT is enabled on router R1.

The routing protocol that is enabled between routers R1, R2 and R3 is RIPv2.

R1 sends the default route into RIPv2 for the internal routers to forward internet traffic to R1.

You have console access on R1, R2 and R3 devices. Use only show commands to troubleshoot the issues.

R1 router clock is synchronized with ISP router R2 is supposed to receive NTP updates from R1. But you observe that R2 clock is not synchronized with R1. What is the reason R2 is not receiving NTP updates from R1?

A. The IP address that is used in the NTP configuration on R2 router is incorrect.

B. The NTP server command not configured on R2 router.

C. R2 router Ethernet interface that is connected to R1 is placed in shutdown condition.

D. R1 router Ethernet interface that is connected to R2 is placed in shutdown condition.

Answer: A

Explanation:

Check the below configuration for this


Question No: 18

WAN data link encapsulation types include which of the following? (Choose two.)

A. T1

B. Frame Relay

C. DSL

D. PPP

E. ISDN

Answer: B,D


Question No: 19

Refer to the exhibit.

A network technician is unable to ping from R1 to R2. Using the output of the show interfaces serial0/1 command, what should the administrator do to correct the problem?

A. Replace the serial cable between R1 and R2.

B. Reseat the serial connectors on the R1 and R2 routers.

C. Configure the serial0/1 interface on R2 with the no shutdown command.

D. Configure the serial0/1 interface on R1 with the clock rate 56000 command.

E. Configure the serial0/1 interface on R1 with the ip address 192.1.1.7 255.255.255.252 command.

Answer: C


P.S. Easily pass 100-105 Exam with Thedumpscentre Vivid Dumps & pdf vce, Try Free: http://www.thedumpscentre.com/100-105-dumps/ (347 New Questions)