Want to know Testking ccna 200 125 torrent Exam practice test features? Want to lear more about Cisco CCNA Cisco Certified Network Associate CCNA (v3.0) certification experience? Study Verified Cisco cisco 200 125 answers to Avant-garde ccna 200 125 ebook questions at Testking. Gat a success with an absolute guarantee to pass Cisco 200 125 ccna (CCNA Cisco Certified Network Associate CCNA (v3.0)) test on your first attempt.
Q81. - (Topic 4)
A network administrator needs to configure a serial link between the main office and a remote location. The router at the remote office is a non-Cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?
A. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# no shut
B. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# encapsulation ppp
Main(config-if)# no shut
C. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# encapsulation frame-relay
Main(config-if)# authentication chap Main(config-if)# no shut
D. Main(config)# interface serial 0/0
Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ietf
Main(config-if)# no shut
Answer: B
Explanation:
With serial point to point links there are two options for the encapsulation. The default, HDLC, is Cisco proprietary and works only with other Cisco routers. The other option is PPP which is standards based and supported by all vendors.
Q82. - (Topic 7)
Which router IOS commands can be used to troubleshoot LAN connectivity problems? (Choose three.)
A. ping
B. tracert
C. ipconfig
D. show ip route
E. winipcfg
F. show interfaces
Answer: A,D,F
Explanation:
Ping, show ip route, and show interfaces are all valid troubleshooting IOS commands. Tracert, ipconfig, and winipcfg are PC commands, not IOS.
Q83. - (Topic 5)
Which two are features of IPv6? (Choose two.)
A. anycast
B. broadcast
C. multicast
D. podcast
E. allcast
Answer: A,C
Explanation:
IPv6 addresses are classified by the primary addressing and routing methodologies common in networking: unicast addressing, anycast addressing, and multicast addressing.
✑ A unicast address identifies a single network interface. The Internet Protocol
delivers packets sent to a unicast address to that specific interface.
✑ An anycast address is assigned to a group of interfaces, usually belonging to different nodes. A packet sent to an anycast address is delivered to just one of the member interfaces, typically the nearest host, according to the routing protocol’s definition of distance. Anycast addresses cannot be identified easily, they have the same format as unicast addresses, and differ only by their presence in the network at multiple points. Almost any unicast address can be employed as an anycast address.
✑ A multicast address is also used by multiple hosts, which acquire the multicast address destination by participating in the multicast distribution protocol among the network routers. A packet that is sent to a multicast address is delivered to all interfaces that have joined the corresponding multicast group.
Q84. - (Topic 5)
A national retail chain needs to design an IP addressing scheme to support a nationwide network. The company needs a minimum of 300 sub-networks and a maximum of 50 host addresses per subnet. Working with only one Class B address, which of the following subnet masks will support an appropriate addressing scheme? (Choose two.)
A. 255.255.255.0
B. 255.255.255.128
C. 255.255.252.0
D. 255.255.255.224
E. 255.255.255.192
F. 255.255.248.0
Answer: B,E
Explanation:
Subnetting is used to break the network into smaller more efficient subnets to prevent excessive rates of Ethernet packet collision in a large network. Such subnets can be arranged hierarchically, with the organization's network address space (see also Autonomous System) partitioned into a tree-like structure. Routers are used to manage traffic and constitute borders between subnets.
A routing prefix is the sequence of leading bits of an IP address that precede the portion of the address used as host identifier. In IPv4 networks, the routing prefix is often expressed as a "subnet mask", which is a bit mask covering the number of bits used in the prefix. An IPv4 subnet mask is frequently expressed in quad-dotted decimal representation, e.g., 255.255.255.0 is the subnet mask for the 192.168.1.0 network with a 24-bit routing prefix (192.168.1.0/24).
Q85. - (Topic 8)
Which two statements about northbound and southbound APIs are true? (Choose two.)
A. Only southbound APIs allow program control of the network.
B. Only northbound APIs allow program control of the network.
C. Only southbound API interfaces use a Service Abstraction Layer.
D. Only northbound API interfaces use a Service Abstraction Layer.
E. Both northbound and southbound API interfaces use a Service Abstraction Layer.
F. Both northbound and southbound APIs allow program control of the network.
Answer: B,C
Q86. - (Topic 8)
Which address class includes network 191.168.0.1/27?
A. Class C
B. Class B
C. Class D
D. Class A
Answer: B
Q87. - (Topic 4)
The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command?
A. This command should be executed from the global configuration mode.
B. The IP address 10.121.16.8 is the local router port used to forward data.
C. 102 is the remote DLCI that will receive the information.
D. This command is required for all Frame Relay configurations.
E. The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC.
Answer: E
Explanation:
Broadcast is added to the configurations of the frame relay, so the PVC supports broadcast, allowing the routing protocol updates that use the broadcast update mechanism to be forwarded across itself.
Q88. - (Topic 4)
What occurs on a Frame Relay network when the CIR is exceeded?
A. All TCP traffic is marked discard eligible.
B. All UDP traffic is marked discard eligible and a BECN is sent.
C. All TCP traffic is marked discard eligible and a BECN is sent.
D. All traffic exceeding the CIR is marked discard eligible.
Answer: D
Explanation:
Committed information rate (CIR): The minimum guaranteed data transfer rate agreed to by the Frame Relay switch. Frames that are sent in excess of the CIR are marked as discard eligible (DE) which means they can be dropped if the congestion occurs within the Frame Relay network.
Note: In the Frame Relay frame format, there is a bit called Discard eligible (DE) bit that is used to identify frames that are first to be dropped when the CIR is exceeded.
Q89. DRAG DROP - (Topic 6)
Drag the security features on the left to the specific security risks they help protect against on the right. (Not all options are used.)
Answer:
Q90. CORRECT TEXT - (Topic 4)
A corporation wants to add security to its network. The requirements are:
✑ Host B should be able to use a web browser (HTTP) to access the Finance Web Server.
✑ Other types of access from host B to the Finance Web Server should be blocked.
✑ All access from hosts in the Core or local LAN to the Finance Web Server should be blocked.
✑ All hosts in the Core and on local LAN should be able to access the Public Web Server.
You have been tasked to create and apply a numbered access list to a single outbound interface. This access list can contain no more than three statements that meet these requirements.
Access to the router CLI can be gained by clicking on the appropriate host.
✑ All passwords have been temporarily set to “cisco”.
✑ The Core connection uses an IP address of 198.18.132.65.
✑ The computers in the Hosts LAN have been assigned addresses of 192.168.201.1
– 192.168.201.254.
✑ host A 192.168.201.1
✑ host B 192.168.201.2
✑ host C 192.168.201.3
✑ host D 192.168.201.4
✑ The Finance Web Server has been assigned an address of 172.22.237.17.
✑ The Public Web Server in the Server LAN has been assigned an address of 172.22.237.18.
Answer:
Please check the below explanation for all details.
Explanation:
We should create an access-list and apply it to the interface that is connected to the Server LAN because it can filter out traffic from both S2 and Core networks. To see which interface this is, use the “show ip interface brief” command:
Macintosh HD:Users:danielkeller:Desktop:Screen Shot 2015-11-17 at 3.24.34 PM.png From this, we know that the servers are located on the fa0/1 interface, so we will place our numbered access list here in the outbound direction.
Corp1#configure terminal
Our access-list needs to allow host B – 192.168125.2 to the Finance Web Server 172.22.109.17 via HTTP (port 80), so our first line is this:
Corp1(config)#access-list 100 permit tcp host 192.168.125.2 host 172.22.109.17 eq 80
Then, our next two instructions are these:
✑ Other types of access from host B to the Finance Web Server should be blocked.
✑ All access from hosts in the Core or local LAN to the Finance Web Server should be blocked.
This can be accomplished with one command (which we need to do as our ACL needs to be no more than 3 lines long), blocking all other access to the finance web server: Corp1(config)#access-list 100 deny ip any host 172.22.109.17
Our last instruction is to allow all hosts in the Core and on the local LAN access to the Public Web Server (172.22.109.18)
Corp1(config)#access-list 100 permit ip host 172.22.109.18 any Finally, apply this access-list to Fa0/1 interface (outbound direction) Corp1(config)#interface fa0/1
Corp1(config-if)#ip access-group 100 out
Notice: We have to apply the access-list to Fa0/1 interface (not Fa0/0 interface) so that the access-list can filter traffic coming from both the LAN and the Core networks.
To verify, just click on host B to open its web browser. In the address box type
http://172.22.109.17 to check if you are allowed to access Finance Web Server or not. If
your configuration is correct then you can access it.
Click on other hosts (A, C and D) and check to make sure you can’t access Finance Web Server from these hosts. Then, repeat to make sure they can reach the public server at 172.22.109.18. Finally, save the configuration
Corp1(config-if)#end
Corp1#copy running-config startup-config