Guaranteed 200-601 Dumps Questions 2021

NEW QUESTION 1
What percentage of an I/O connection would you set the RPI in order to ensure the application has the most current data?

• A. RPI at 50% of IO rate
• B. RPI at 25% of IO rate
• C. PI to 25% of PAC scan rate
• D. Set RPI to 50% of PAC scan rate

Answer: A

NEW QUESTION 2
A cookie cutter machine requires 2 standard controllers and a safety controller. All of these controllers and machine level I/O have been placed on VLAN 104. Both standard controllers must monitor a photocell on this machine. Which IP address is used to transfer this status information?

• A. 10.17.104.16
• B. 192.168.1.16
• C. 239.192.3.16
• D. 239.192.254.16

Answer: C

NEW QUESTION 3
Refer to the exhibit.

You are required to implement traffic segmentation in the network. See the table for relevant device details:
L2SW4, L2SW5, and L2SW6 are connected to L3SW1 with 802.1Q trunks with VLAN 191 and VLAN 398 allowed on the trunk.
You have the following information from L3SW1:
L3SW1# show run interfaces
interface Vlan1 no ip address shutdown
!
interface Vlan2
ip address 10.2.2.2 255.255.255.248
!
interface Vlan191
ip address 10.10.27.126 255.255.255.192
!
interface Vlan200
ip address 10.20.20.1 255.255.255.248
!
interface Vlan398
ip address 10.15.153.1 255.255.255.0
L3SW1# show ip route
*** Output Omitted ***
10.0.0.0/8 is variably subnetted, 5 subnets, 3 masks C 10.2.2.1/29 is directly connected, Vlan2
C 10.10.27.64/26 is directly connected, Vlan191 C 10.15.153.0/24 is directly connected, Vlan398 C 10.20.20.0/29 is directly connected, Vlan200 S 10.200.200.0/24 [1/0] via 10.20.20.2
S* 0.0.0.0/0 [1/0] via 10.2.2.1
You are required to implement a configuration that will meet the following connectivity requirements:
• The Administrator's Station must have full access to PanelView
• PanelView should have limited access, based on specific TCP ports, to PLC#1 and I/O#1
• The Administrator's Station should have no access to PLC#1 and I/O#1
• PLC#1 and I/O#1 should be able to communicate with each other on any port Which action will allow you to meet the connectivity requirements?

• A. Put interface VLAN 191 and interface VLAN 398 into different Virtual Routing and Forwarding (VRF) instances on L3SW1
• B. Deploy an inbound ACL on interface VLAN 191 to control the traffic from the Administrator's Station and PanelView to PLC#1 and I/O#1
• C. No change is required, the traffic is already limited appropriately by the VLAN segmentation
• D. Implement an ACL on Firewall1 to control the traffic flow between VLAN 191 and VLAN 398

Answer: B

NEW QUESTION 4
Which statement is correct regarding ProfiNET communication classes?

• A. ProfiNET-RT traffic is carried in UDP and TCP packets
• B. ProfiNET-NRT is used to carry time critical status information
• C. ProfiNET-IRT requires switches with hardware time scheduling capabilities
• D. ProfiNET-NRT is prioritized as Layer-2 Class-of-Service 1 (CoS 1)

Answer: C

NEW QUESTION 5
Which option allows an EtherNet/IP I/O device to be safely installed where it is subject to water immersion?

• A. The device is rated IP20 and the power wiring is installed securely to the terminal block.
• B. The device is rated IP67 and a power cordset is used.
• C. The device is rated IP67 and immersed to 10 m.
• D. The device is rated IP20 and immersed to 10 m.

Answer: B

NEW QUESTION 6
Exhibit:

Which two statements are correct for a safe wiring installation to the terminal block of the switch or endpoint? (Choose two.)

• A. Insert a green ground wire into the terminal block that is marked RT for return.
• B. Verify that DC power is live and within 24 VDC voltage range before starting wiring.
• C. Verify that the DC power circuit includes an overcurrent protective device that limits the DC current to 5 A.
• D. Because this is a low-voltage DC circuit, anyone can install this wiring without electrical training or qualifications.
• E. Connect the positive 24 VDC conductor to the V terminal and connect the negative 24 VDC return wire to the RT terminal.
• F. A ground wire can optionally be connected to the screw terminal on the front of the switch.

Answer: CE

NEW QUESTION 7
A ProfiNET management system operator is unable to add a ProfiNET Conformance Class B device to a SIMATIC management station. The device is connected to interface FastEthernet1/3. Based on the provided CLI output, which statement is correct?
switch#show profinet lldp Fa1/1 port-003-00000 On Fa1/2 port-004-00000 On Fa1/3 port-005-00000 Off Fa1/4 port-006-00000 Off Fa1/5 port-007-00000 On Fa1/6 port-008-00000 Off Fa1/7 port-009-00000 On Fa1/8 port-010-00000 Off

• A. LLDP has been disabled on this switch
• B. The connected device is not sending LLDP packets with ProfiNET extensions
• C. The port label needs to be changed on interface FastEthernet 1/3 to "port-003-00000"
• D. ProfiNET is disabled on this switch

Answer: B

NEW QUESTION 8
What security component can be deployed to increase the defense in depth and specifically can be positioned against 'man-in-the-middle' attack?

• A. Deploy 802.1AE
• B. Deploy 802.1X
• C. Deploy 802.1Q
• D. Deploy 802.1AX

Answer: A

NEW QUESTION 9
Which in-depth approach is used when deploying defense in an industrial zone?

• A. Besides using a dedicated firewall / DMZ construction use an IOS based firewall on the WAN router connecting the industrial site to the Internet.
• B. Use NTP to make sure that time stamps of log messages are synchronized such that you can do root cause analysis.
• C. Deploy an IDS solution with knowledge about industrial protocols in the industrial zone in combination with a firewall.
• D. Use multiple firewalls from different vendors in such a way that network traffic will have to traverse both firewalls so that security holes of one firewall is caught by the other firewall.

Answer: C

NEW QUESTION 10
A cookie cutter machine requires 2 standard controllers and a safety controller. All of these controllers and machine level I/O have been placed on VLAN 104. The safety controller must monitor an emergency stop connected to an I/O adapter on an adjacent machine (VLAN 105). Which packet type will be used?

• A. UDP Multicast TTL = 1
• B. UDP Multicast TTL = 2
• C. UDP Unicast
• D. TCP Unicast

Answer: C

NEW QUESTION 11
Given the CIA triad elements, which ensures first that the data is encrypted and secure, second that the data is trustworthy, and third that the data is accessible by those who need it?

• A. CIA
• B. ICA
• C. ACI
• D. CAI

Answer: A

NEW QUESTION 12
Refer to the exhibit. Which lines represent a CIP connection being established between two devices?

• A. 2914 and 2915
• B. 2918 and 2921
• C. 2920 and 2924
• D. 2937 and 2940

Answer: B

NEW QUESTION 13
Which describes the relationship between a workgroup bridge?

• A. Wired clients of a workgroup bridge can communicate, through the workgroup bridge, with wireless clients of an autonomous or a controller-based access point
• B. Wireless clients of a controller-based AP can communicate, through the workgroup bridge, with wireless clients of an autonomous access point
• C. Wireless clients of an autonomous access point can communicate with wired clients of a workgroup bridge, but Wireless clients of a controller-based access point cannot communicate with wired clients of a workgroup bridge
• D. Wireless clients of a controller-based access point can communicate with wired clients of a workgroup bridge, but Wireless clients of an autonomous access point cannot communicate with wired clients of a workgroup bridge

Answer: A

NEW QUESTION 14
Which is an issue with running CIP Motion on a REP network and identifies an alternate resiliency protocol that works for CIP Motion?

• A. CIP Motion requires a star topology which is not supported by RE
• B. DLR is a suitable resiliency protocol for CIP motion.
• C. REP convergence is not fast enoug
• D. DLR is a suitable resiliency protocol for CIP motion.
• E. CIP Motion requires a star topology which is not supported by RE
• F. RPVST+ is a suitable resiliency protocol for CIP motion.
• G. REP convergence is not fast enoug
• H. RPVST+ is a suitable resiliency protocol for CIP motion.

Answer: B

NEW QUESTION 15
What is the reason that ProfiNET frames are discarded by default on Catalyst switches?

• A. ProfiNET uses a nonstandard Ethernet frame format
• B. The frames have an 802.1q tag with VLAN ID equal to 0 (zero)
• C. Catalyst switches do not support ProfiNET traffic
• D. A ProfiNET VLAN must be configured and enabled on a Catalyst switch

Answer: B

NEW QUESTION 16
Which three of the following components must be elected before the Spanning Tree Protocol can converge in a switched LAN? (Choose three.)

• A. designated ports
• B. duplex operating mode
• C. fast mode ports
• D. root bridge
• E. root ports
• F. BDPU priority

Answer: ADE

NEW QUESTION 17
Which CLI command will display IGMP snooping information in a Cisco IE2000 or Stratix 5700 switch?

• A. switch#show snooping ip igmp
• B. switch#show igmp snooping
• C. switch#show ip igmp snooping
• D. switch#show ip snooping

Answer: C

NEW QUESTION 18
Refer to the exhibit.

What issue does this topology present for the represented traffic flow?

• A. Standard Produce/Consume traffic is not suitable for an 802.11 wireless environment.
• B. Only one of the Work Group Bridges can transmit at a time, because 802.11 is half duplex.
• C. The Converged Plant-wide Ethernet best practices for 802.11 wireless don't allow for PAC to PAC traffic.
• D. I/O control traffic should utilize the 2.4 GHz band based on best practices.

Answer: B