Exam Code: 201-450 (Practice Exam Latest Test Questions VCE PDF)
Exam Name: LPIC-2 Exam 201 Part 1 of 2 version 4.5
Certification Provider: LPI
Free Today! Guaranteed Training- Pass 201-450 Exam.
New LPI 201-450 Exam Dumps Collection (Question 5 - Question 14)
New Questions 5
Which of the following commands shows capabilities and usable frequencies for the wireless interface wlan0?
A. iw phy pyh0 info
B. iw dev wlan0 info
C. iw dev wlan0 show
D. iw phy wlan0 show
E. iw phy0 show
Answer: A
New Questions 6
Which of the following are common backup systems used in Linux? (Choose TWO correct answers.)
A. Amanda
B. Bacula
C. DrBackup
D. BREWBackup
E. SARcheck
Answer: AB
New Questions 7
Which single command will simulate a failed device within a RAID 5 array?
A. mdadm --remove /dev/md0 /dev/sdd1
B. mdadm --zero-superblock /dev/sdf3
C. mdadm --force-fault /dev/md2 /dev/sde2
D. mdadm --fail /dev/md0 /dev/sdc1
E. mdadm /dev/md0 --offline /dev/sdc1
Answer: D
New Questions 8
Which command is used to install a GRUB boot loader into the master boot record?
A. grub-install
B. grub-mkconfig
C. grub-install-mbr
D. grub-glue-mbr
E. grub-mbr-setup
Answer: A
New Questions 9
Which of the following commands will erase the contents of the /dev/sdb3 partition?
A. rm /dev/sdb3
B. dd if=/dev/zero of=/dev/sdb3
C. dd of=/dev/zero if=/dev/sdb3
D. umount /dev/sdb3
Answer: B
New Questions 10
What is incorrect about these entries in /etc/hosts which could be causing host name lookup problems with host2?
host1 192.168.1.12
host2 192.168.1.12
A. Two host names are using the same IP address.
B. The server doing the query is on a different subnet.
C. The fields are out of order.
D. host2 is not a fully qualified domain name.
Answer: C
New Questions 11
Which of the following commands is used to set up a RAID volume?
A. makerd
B. mdadm
C. mkfs.raid
D. makeraid
E. rdconfig
Answer: B
New Questions 12
The IDE hard drive /dev/hda does not have DMA enabled. Which command must be run to enable DMA on it?
A. hdparm -d /dev/hda
B. hdparm --dma /dev/hda
C. hdparm --dma /dev/hda1
D. hdparm -d /dev/hda1
E. hdparm -d 1 /dev/hda
Answer: E
New Questions 13
Which RAID level value must be used with Linux software RAID in order to create an array of mirrored devices?
A. 1
B. 5
C. 6
D. container
E. mirrorstripe
Answer: A
New Questions 14
The following command has just been run successfully: cd /opt; tar xvf /dev/nst0;
What will happen if the command sequence is run again?
A. An error saying that there is no tape present is generated because the tape has been ejected after being used.
B. The contents of /opt will be restored again.
C. The entire contents of /opt will be replaced with the contents of the next file on the tape.
D. The contents of /opt will have additional content added from the next file on the tape.
Answer: D
Recommend!! Get the Best Quality 201-450 dumps in VCE and PDF From 2passeasy, Welcome to download: https://www.2passeasy.com/dumps/201-450/ (New Q&As Version)