we provide 100% Guarantee Cisco 300 101 route exam question which are the best for clearing ccnp 300 101 pdf test, and to get certified by Cisco ROUTE Implementing Cisco IP Routing. The ccnp dumps 300 101 Questions & Answers covers all the knowledge points of the real ccnp dumps 300 101 exam. Crack your Cisco cisco 300 101 dump Exam with latest dumps, guaranteed!
P.S. 100% Guarantee 300-101 software are available on Google Drive, GET MORE: https://drive.google.com/open?id=1IPFRgHPm2o-6qCPBhQuk3ypuFkiGdV3b
New Cisco 300-101 Exam Dumps Collection (Question 5 - Question 14)
New Questions 5
CORRECT TEXTA network engineer enables OSPF on a Frame Relay WAN connecton to various remote stes, but no OSPF adiacencies come up Which two actions are possible solutions for thisissue? (Choose Two)
A Change the network type to point-to-murpont under WAN interface
B. Enable virtual Inks
C. Change the networktype to nonbroadcast mutpoint access
D. Configure the neighbor command under OSPF process for each remote ste
E. Ensure that the OSPF process number matches among all remote stes
Answer: A, D
New Questions 6
How should a router that is being used in a Frame Relay network be configured to keep split horizon issues from preventing routing updates?
A. Configure a separate subinterface for each PVC with a unique DLCI and subnet assigned to the
subinterface.
B. Configure each Frame Relay circuit as a point-to-point line to support multicast and broadcast traffic.
C. Configure many subinterfaces in the same subnet.
D. Configure a single subinterface to establish multiple PVC connections to multiple remote router interfaces.
Answer: A
Explanation: EXPLANATION
If you have a serial port configured with multiple DLCIs connected to multiple remote sites, split horizon rules, stop route updates received on an interface from being sent out the same interface. By creating subinterfaces for each PVC, you can avoid the split horizon issues when using Frame Relay. http://www.indiabix.com/networking/wide-area- networks/015004
New Questions 7
Which statement describes what this command accomplishes when inside and outside interfaces are correctly identified for NAT?
ip nat inside source static tcp 192.168.1.50 80 209.165.201.1 8080 extendable
A. It allows host 192.168.1.50 to access external websites using TCP port 8080.
B. It allows external clients coming from public IP 209.165.201.1 to connect to a web server at 192.168.1.50.
C. It allows external clients to connect to a web server hosted on 192.168.1.50.
D. It represents an incorrect NAT configuration because it uses standard TCP ports.
Answer: C
New Questions 8
Refer to the exhibit. Which statement is true?
A. Traffic from the 172.16.0.0/16 network will be blocked by the ACL.
B. The 10.0.0.0/8 network will not be advertised by Router B because the network statement for the 10.0.0.0/8 network is missing from Router B.
C. The 10.0.0.0/8 network will not be in the routing table on Router B.
D. Users on the 10.0.0.0/8 network can successfully ping users on the 192.168.5.0/24 network, but users on the 192.168.5.0/24 cannot successfully ping users on the 10.0.0.0/8 network.
E. Router B will not advertise the 10.0.0.0/8 network because it is blocked by the ACL.
Answer: E
New Questions 9
Which statement is true concerning 6to4 tunneling?
A. IPv4 traffic is encapsulated with an IPv6 header.
B. The edge routers can use any locally configured IPv6 address.
C. Hosts and routers inside a 6to4 site will need a special code.
D. An edge router must use IPv6 address of 2002::/16 in its prefix.
Answer: D
Explanation:
6to4 tunnels use IPv6 addresses that concatenate 2002::/16 with the 32-bit IPv4 address of the edge router, creating a 48-bit prefix.
New Questions 10
Refer to the Exhibit.
What is the correct configuration to enable router P4 to exchange RIP routing updates with router P1 but not with router P3?
A. P4(Config)# interface fa0/0P4(Config-if)# neighbor 192.168.10.3P4(config-if)# passive- interface fa0/0
B. P4(config)# router ripP4(config-router)#neighbor 192.168.10.3P4(Config- router)#passive-interface fa0/0
C. P4(config)# interface fa0/0P4(config-if)# neighbor 192.168.10.3P4(config-if)# passive interface192.168.10.34
D. P4(config)# router ripP4(config-router)# neighbor 162.168.10.34 no broadcastP4(config- router)# passive-interface fa0/0
Answer: B
Explanation:
When you configure router P1 to be the nieghtobr of P4 with a passive interface, the RIP routing updates will be exchanged with the neighbor only.
New Questions 11
Which two commands must you configure on a DMVPN hub to enable phase 3? (Choose two)
A. ip nhrp interest
B. ip nhrp redirect
C. ip nhrp shortcut
D. ip network-id
E. ip nhrp map
F. ip redirects
Answer: D,E
New Questions 12
Which traffic characteristic is the reason that UDP traffic that carries voice and video is assigned to the queue only on a link that is at least 768 kbps?
A. typically is not fragmented
B. typically is fragmented
C. causes windowing
D. causes excessive delays for video traffic
Answer: A
New Questions 13
Refer to the exhibit. Router DHCP is configured to lease IPv4 and IPv6 addresses to clients on ALS1 and ALS2. Clients on ALS2 receive IPv4 and IPv6 addresses. Clients on ALS1 receive IPv4 addresses. Which configuration on DSW1 allows clients on ALS1 to receive IPv6 addresses?
A. DSW1 (config-if)# ipv6 helper address 2002:404:404::404:404
B. DSW1 (config)#ipv6 route 2002:404:404::404:404/128 FastEthernet 1/0
C. DSW1 (dhcp-config)# default-router 2002:A04:A01::A04:A01
D. DSW1 (config)# ipv6 dhcp relay destination 2002:404:404::404:404 GigabitEthernet 1/2
Answer: D
New Questions 14
Refer to the exhibit.
Based upon the configuration, you need to understand why the policy routing match counts are not increasing. Which would be the first logical step to take?
A. Confirm if there are other problematic route-map statements that precede divert.
B. Check the access list for log hits.
C. Check the routing table for 212.50.185.126.
D. Remove any two of the set clauses. (Multiple set clause entries will cause PBR to use the routing table.)
Answer: B
Explanation: Explanation
First we should check the access-list log, if the hit count does not increase then no packets are matched the access-list -> the policy based routing match counts will not increase.
Recommend!! Get the 100% Guarantee 300-101 dumps in VCE and PDF From Certleader, Welcome to download: https://www.certleader.com/300-101-dumps.html (New 487 Q&As Version)