Our pass rate is high to 98.9% and the similarity percentage between our ccnp switch 300 115 study guide and real exam is 90% based on our seven-year educating experience. Do you want achievements in the Cisco 300 115 vce exam in just one try? I am currently studying for the Cisco certprepare 300 115 exam. Latest Cisco ccnp switch 300 115 pdf Test exam practice questions and answers, Try Cisco examcollection 300 115 Brain Dumps First.
P.S. Download 300-115 questions pool are available on Google Drive, GET MORE: https://drive.google.com/open?id=1CfKI5pbjCPmPD71IOn4nWDyRdJ9zMspQ
New Cisco 300-115 Exam Dumps Collection (Question 15 - Question 24)
New Questions 15
Refer to the exhibit.
Which two effects of this configuration are true? (Choose two.)
A. R1 becomes the active router
B. If R2 goes down, R1 becomes active but reverts to standby when R2 comes back online
C. Hello messages are sent to multicast address 224.0.0.5.
D. If R1 goes down, R2 becomes active but reverts to standby when R1 comes back online.
E. R1 goes down, R2 becomes active and remains the active device when R1 comes back online
F. R1 becomes the standby router.
Answer: A,E
New Questions 16
Refer to the exhibit.
Which two commands ensure that dsw1 becomes root bridge for vlan 10 ?
A. DSW2(Config)#spanning-tree vlan 10 priority 61440
B. DSW2(Config)#spanning-tree vlan 10 priority 4066
C. DSW2(Config)#spanning-tree vlan 20 priority 0
D. DSW2(Config)#spanning-tree vlan 10 priority root
E. DSW2(Config)#spanning-tree vlan 10 port-priority 0
Answer: B,D
New Questions 17
In which state does the standby virtual gateway take election?
A. learn
B. listen
C. init
D. reply
Answer: B
New Questions 18
Which two configurations can you apply to a port so that it tags traffic with VLAN 915? (Choose two.)
A. interface GigabitEthernet0/0 switchport mode access switchport access vlan 915
B. interface GigabitEthernet0/0 switchport mode trunk
switchport trunk encapsulation dot1q switchport trunk allowed vlan 915
C. interface GigabitEthernet0/0 switchport mode access switchport voice vlan 915 switchport access vlan 915
D. interface GigabitEthernet0/0.915 encapsulation dot1q 915
E. interface GigabitEthernet0/0.915 switchport mode access
switchport access vlan 915
Answer: B,D
New Questions 19
A network engineer is trying to prevent users from connecting unauthorized equipment to a production network. Which option can be campus-wide to satisfy this requirement?
A. IP Source Guard
B. switch port block
C. Uplink fast
D. private VLAs
E. BPDU Guard
Answer: A
New Questions 20
Which describes the default load balacing scheme used by the Gateway Load Balancing Protocol (GLBP)?
A. Per host using a strict priority scheme
B. Per session using a round-robin scheme
C. Per session using a strict priority scheme
D. Per GLBP group using a strict priority scheme
E. Per host basis using a round robin-scheme
F. Per GLBP group using a round-robin scheme
Answer: E
New Questions 21
Which feature do you implement so that an interface enters the root inconsistent state if it receives a superior BPDU?
A. DPDU filter
B. root guard
C. BPDU guard
D. loop guard
Answer: B
New Questions 22
Which three statements are correct with regard to the IEEE 802.1Q standard? (Choose three)
A. The IEEE 802.1Q frame format adds a 4 byte field to a Ethernet frame
B. The packet is encapsulated with a 26 byte header and a 4 byte FCS
C. The protocol uses point-to-multipoint connectivity
D. The protocol uses point-to-point connectivity
E. The IEEE 802.1Q frame uses multicast destination of 0x01-00-0c-00-00
F. The IEEE 802.1Q frame retains the original MAC destination address
Answer: A,D,F
New Questions 23
Which two statements about the HSRP priority are true? (Choose two)
A. To assign the HSRP router priority in a standby group, the standby group-number priority priority-value global configuration command must be used.
B. The default priority of a router is zero (0).
C. The no standby priority command assigns a priority of 100 to the router.
D. Assuming that preempting has also been configured, the router with the lowest priority in an HSRP group would become the active router.
E. When two routers in an HSRP standby group are configured with identical priorities, the router with the highest configured IP address will become the active router.
Answer: C,E
New Questions 24
Which feature prevents from sending BPDUs on a portfast enabled port?
A. BPDU guard
B. PortFast
C. root guard
D. BPDU filtering
Answer: D
100% Refresh Cisco 300-115 Questions & Answers shared by Certleader, Get HERE: https://www.certleader.com/300-115-dumps.html (New 522 Q&As)