Everything youll need in the JN0-360 certification exam can be included from the Juniper JN0-360 practice materials. Each of our professionals keep the Juniper Juniper certification exam dumps updated and revised constantly. The particular price can be reasonable and also the time anyone spend can be worthy of. Every single JN0-360 exam question is equipped with correct and verified answer in particulars. Regular updates about the basis of the true Juniper JN0-360 exam questions. Every consumer can require a quiz before purchasing our Juniper Juniper merchandise. Come for you to http://www.Examcollection.com right now. All of the valuable JN0-360 simulated tests is going to be presented to you personally. Download the check engine software, and preview the Juniper exam from anywhere and anytime.
2021 Sep JN0-360 exam engine
Q41. What are three ways to configure IPv6 addresses in your network? (Choose three.)
A. Statically configure your IPv6 addresses.
B. Configure your IPv6 addresses using stateless auto configuration.
C. Configure your IPv6 addresses by setting up a DHCPv6 server.
D. Configure your IPv6 addresses by assigning your router a prefix list.
E. Configure your IPv6 addresses by configuring support for unicast-arp-negotiation.
Answer: ABC
Q42. Router A is an OSPF router connected to both Area 0 and Area 1 Area 1 has been configured as a stub area Which two LSA types does Router A suppress from Area 1 ?
A. Router LSA
B. External LSA
C. Summary LSA
D. ASBR Summary LSA
Answer: BD
Q43. You are logged into a PE router participating in a Layer 3 VPN as defined in RFC 4364. You would like to ping the locally connected CE router's interface. The address of the interface is 192.168.1.1; the VPN routing-instance is named VPN-A. Which command will accomplish this task?
A. ping routing-instance VPN-A 192.168.1.1
B. ping instance VPN-A 192.168.1.1
C. ping vpn-instance VPN-A 192.168.1.1
D. ping VPN-A 192.168.1.1
E. ping mpls l3vpn VPN-A 192.168.1.1
Answer: E
Q44. You own a small company and need to assign IPv6 addresses to your routers. Because you want to follow the guidelines spelled out in RFC 3177, you want to design your network with the correct prefixes. Which prefix would your ISP likely allocate to your company?
A. 47-bit prefix
B. 48-bit prefix
C. 64-bit prefix
D. 128-bit prefix
Answer: B
Q45. You are logged into a router and issue the command show route protocol bgp. You see that you have received the route 10 0.4/24 from two different peers Both peers were learned using IBGP and Local-Preference. MED, Origin, and AS-path are equal.
Which criterion is used for this situation?
A. cluster length
B. router ID (RID)
C. peer ID
D. IGP cost
Answer: D
Replace JN0-360 free exam:
Q46. What are two characteristics of a traditional Ethernet LAN? (Choose two.)
A. Nodes share a physical medium.
B. Nodes can successfully transmit simultaneously.
C. It consists of a single broadcast domain.
D. Nodes use a step-up algorithm when collisions are detected.
Answer: AC
Q47. To prevent fragmentation issues across a GRE tunnel, which MTU value is recommended for the tunnel to accommodate most IP packets?
A. 1476
B. 1492
C. 1500
D. 1524
Answer: D
Q48. Your area border router (ABR) receives type 1.2 and 5 link-state advertisements (LSAs) from a non-backbone area.
What would the ABR do with the information learned from the non-backbone area?
A. The ABR will generate type 2 and 3 LSAs and flood type 5 LSAs to the backbone area
B. The ABR will generate only type 3 LSAs and flood only type 5 LSAs to the backbone area
C. The ABR will generate type 3 and 4 LSAs. And flood type 5 LSAs to the backbone area
D. The ABR will generate only type 4 LSAs and flood only type 5 LSAs to the backbone area
Answer: C
Q49. Click the Exhibit button
You work for the regional Internet service provider shown in the exhibit You have a partial BGP table and are receiving a 10 100/16 route from your upstream ISP You have been asked to configure a default route that can be sent to your downstream customer This route should forward customer traffic toward your upstream Tier 11SP as long as the 10.100/16 route is present.
What would accomplish this goal?
A. Create and announce an aggregate default route
B. Create and announce a static default route with a next-hop of discard
C. Create and announce a static default route with a next-hop of reject
D. Create and announce a generated default route
E. Create an advertise-map with exist-map
Answer: E
Q50. In the evaluation of an RSTP configuration BPDU, which two values are contained in the Bridge ID value? (Choose two)
A. root bridge address
B. priority
C. originating bridge address
D. port number
Answer: BC