Q1. - (Topic 5)
Refer to the exhibit.
What statement is true of the configuration for this network?
A. The configuration that is shown provides inadequate outside address space for translation of the number of inside addresses that are supported.
B. Because of the addressing on interface FastEthernet0/1, the Serial0/0 interface address will not support the NAT configuration as shown.
C. The number 1 referred to in the ip nat inside source command references access-list number 1.
D. ExternalRouter must be configured with static routes to networks 172.16.1.0/24 and 172.16.2.0/24.
Answer: C
Explanation:
The “list 1 refers to the access-list number 1.
Q2. - (Topic 5)
What will happen if a private IP address is assigned to a public interface connected to an ISP?
A. Addresses in a private range will not be routed on the Internet backbone.
B. Only the ISP router will have the capability to access the public network.
C. The NAT process will be used to translate this address to a valid IP address.
D. A conflict of IP addresses happens, because other public routers can use the same range.
Answer: A
Explanation:
Private RFC 1918 IP addresses are meant to be used by organizations locally within their own network only, and cannot be used globally for Internet use.
Q3. - (Topic 7)
What are three values that must be the same within a sequence of packets for Netflow to consider them a network flow? (Choose three.)
A. source IP address
B. source MAC address
C. egress interface
D. ingress interface
E. destination IP address
F. IP next-hop
Answer: A,D,E
Explanation:
Each packet that is forwarded within a router or switch is examined for a set of IP packet attributes. These attributes are the IP packet identity or fingerprint of the packet and determine if the packet is unique or similar to other packets.
Traditionally, an IP Flow is based on a set of 5 and up to 7 IP packet attributes. IP Packet attributes used by NetFlow:
• IP source address
• IP destination address
• Source port
• Destination port
• Layer 3 protocol type
• Class of Service
• Router or switch interface
All packets with the same source/destination IP address, source/destination ports, protocol interface and class of service are grouped into a flow and then packets and bytes are tallied. This methodology of fingerprinting or determining a flow is scalable because a large amount of network information is condensed into a database of NetFlow information called the NetFlow cache.
Reference: http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/ios- netflow/prod_white_paper0900aecd80406232.html
Q4. - (Topic 8)
Which command can you enter to determine whether serial interface 0/2/0 has been configured using HDLC encapsulation?
A. router#show platform
B. router#show interfaces Serial 0/2/0
C. router#show ip interface s0/2/0
D. router#\show ip interface brief
Answer: C
Q5. - (Topic 8)
Which two statements about IPv6 and routing protocols are true? (Choose two.)
A. Link-local addresses are used to form routing adjacencies.
B. OSPFv3 was developed to support IPv6 routing.
C. EIGRP, OSPF, and BGP are the only routing protocols that support IPv6.
D. Loopback addresses are used to form routing adjacencies.
E. EIGRPv3 was developed to support IPv6 routing.
Answer: A,B
Q6. - (Topic 5)
How does a DHCP server dynamically assign IP addresses to hosts?
A. Addresses are permanently assigned so that the host uses the same address at all times.
B. Addresses are assigned for a fixed period of time. At the end of the period, a new request for an address must be made, and another address is then assigned.
C. Addresses are leased to hosts. A host will usually keep the same address by periodically contacting the DHCP server to renew the lease.
D. Addresses are allocated after a negotiation between the server and the host to determine the length of the agreement.
Answer: C
Explanation:
DHCP works in a client/server mode and operates like any other client/server relationship. When a PC connects to a DHCP server, the server assigns or leases an IP address to that PC. The PC connects to the network with that leased IP address until the lease expires. The host must contact the DHCP server periodically to extend the lease. This lease mechanism ensures that hosts that move or power off do not hold onto addresses that they do not need. The DHCP server returns these addresses to the address pool and reallocates them as necessary.
Q7. - (Topic 8)
Which command can you execute to set the user inactivity timer to 10 seconds?
A. SW1(config-line)#exec-timeout 0 10
B. SW1(config-line)#exec-timeout 10
C. SW1(config-line)#absolute-timeout 0 10
D. SW1(config-line)#absolute-timeout 10
Answer: A
Q8. - (Topic 3)
Refer to the exhibit.
Assuming that the entire network topology is shown, what is the operational status of the interfaces of R2 as indicated by the command output shown?
A. One interface has a problem.
B. Two interfaces have problems.
C. The interfaces are functioning correctly.
D. The operational status of the interfaces cannot be determined from the output shown.
Answer: C
Explanation:
The output shown shows normal operational status of the router’s interfaces. Serial0/0 is down because it has been disabled using the “shutdown” command.
Q9. CORRECT TEXT - (Topic 7)
The following have already been configured on the router:
✑ The basic router configuration
✑ The appropriate interfaces have been configured for NAT inside and NAT outside.
✑ The appropriate static routes have also been configured (since the company will be a stub network, no routing protocol will be required)
✑ All passwords have been temporarily set to “cisco”.
The task is to complete the NAT configuration using all IP addresses assigned by the ISP to provide Internet access for the hosts in the Weaver LAN. Functionality can be tested by clicking on the host provided for testing.
Configuration information:
router name – Weaver
inside global addresses – 198.18.184.105 - 198.18.184.110/29 inside local addresses - 192.168.100.17 – 192.168.100.30/28 number of inside hosts – 14
A network associate is configuring a router for the weaver company to provide internet access. The ISP has provided the company six public IP addresses of 198.18.184.105 198.18.184.110. The company has 14 hosts that need to access the internet simultaneously. The hosts in the company LAN have been assigned private space addresses in the range of 192.168.100.17 – 192.168.100.30.
Answer:
The company has 14 hosts that need to access the internet simultaneously but we just have 6 public IP addresses from 198.18.184.105 to 198.18.184.110/29. Therefore we have to use NAT overload (or PAT)
Double click on the Weaver router to open it
Router>enable Router#configure terminal
First you should change the router's name to Weaver
Router(config)#hostname Weaver
Create a NAT pool of global addresses to be allocated with their netmask. Weaver(config)#ip nat pool mypool 198.18.184.105 198.18.184.110 netmask 255.255.255.248
Create a standard access control list that permits the addresses that are to be translated.
Weaver(config)#access-list 1 permit 192.168.100.16 0.0.0.15
Establish dynamic source translation, specifying the access list that was defined in the prior step.
Weaver(config)#ip nat inside source list 1 pool mypool overload
This command translates all source addresses that pass access list 1, which means a source address from 192.168.100.17 to 192.168.100.30, into an address from the pool named mypool (the pool contains addresses from 198.18.184.105 to 198.18.184.110). Overload keyword allows to map multiple IP addresses to a single registered IP address (many-to-one) by using different ports.
The question said that appropriate interfaces have been configured for NAT inside and NAT outside statements.
This is how to configure the NAT inside and NAT outside, just for your understanding:
Weaver(config)#interface fa0/0 Weaver(config-if)#ip nat inside Weaver(config-if)#exit Weaver(config)#interface s0/0 Weaver(config-if)#ip nat outside Weaver(config-if)#end
Finally, we should save all your work with the following command:
Weaver#copy running-config startup-config
Check your configuration by going to "Host for testing" and type:
C :\>ping 192.0.2.114
The ping should work well and you will be replied from 192.0.2.114
Q10. - (Topic 5)
When a DHCP server is configured, which two IP addresses should never be assignable to
hosts? (Choose two.)
A. network or subnetwork IP address
B. broadcast address on the network
C. IP address leased to the LAN
D. IP address used by the interfaces
E. manually assigned address to the clients
F. designated IP address to the DHCP server
Answer: A,B
Explanation:
Network or subnetwork IP address (for example 11.0.0.0/8 or 13.1.0.0/16) and broadcast address (for example 23.2.1.255/24) should never be assignable to hosts. When try to assign these addresses to hosts, you will receive an error message saying that they can’t be assignable.