we provide Download Cisco 200 125 ccna answers which are the best for clearing 125 200 test, and to get certified by Cisco CCNA Cisco Certified Network Associate CCNA (v3.0). The ccna routing and switching 200 125 pdf Questions & Answers covers all the knowledge points of the real ccna routing and switching 200 125 official cert guide library exam. Crack your Cisco 125 200 Exam with latest dumps, guaranteed!

P.S. Download 200-125 paper are available on Google Drive, GET MORE: https://drive.google.com/open?id=1IiiyEYVh7VGuzQjIt9B135ONv4m9W195


New Cisco 200-125 Exam Dumps Collection (Question 14 - Question 23)

New Questions 14

Which effect of the passive-Interface command on R1 is true?

A. It removes the 172.16.0.0 network from all updates on all interfaces on R1.

B. It prevents interface Fa0/0 from sending updates.

C. Interface Fa0/0 operates in RIPv1 mode.

D. It removes the 172.17.0.0 network from all updates on all interfaces on R1.

Answer: B


New Questions 15

Refer to the exhibit. Which two statements are true about the loopback address that is configured on RouterB? (Choose two.)

A. It ensures that data will be forwarded by RouterB.

B. It provides stability for the OSPF process on RouterB.

C. It specifies that the router ID for RouterB should be 10.0.0.1.

D. It decreases the metric for routes that are advertised from RouterB.

E. It indicates that RouterB should be elected the DR for the LAN.

Answer: B,C

Explanation:

A loopback interface never comes down even if the link is broken so it provides stability for the OSPF process (for example we use that loopback interface as the router-id) -

The router-ID is chosen in the order below:

+ The highest IP address assigned to a loopback (logical) interface.+ If a loopback interface is not defined, the highest IP address of all active routeru2021s physical interfaces will be chosen.

-> The loopback interface will be chosen as the router ID of RouterB u2013


New Questions 16

Which three statements about VTP features are true? (Choose three.)

A. VTP works at Layer 3 of the OSI model and requires that a management VLAN IP address be configured.

B. When properly configured, VTP minimizes VLAN misconfigurations and configuration inconsistencies.

C. When properly configured, VTP maintains VLAN configuration consistency and accelerates trunk link negotiation.

D. Each broadcast domain on a switch can have its own unique VTP domain.

E. VTP pruning is used to increase available bandwidth in trunk links.

F. To configure a switch to be part of two VTP domains, each domain must have its own passwords.

G. Client, server, and transparent are valid VTP modes.

Answer: B,E,G


New Questions 17

Which protocol is the Cisco proprietary implementation of FHRP?

A. HSRP

B. VRRP

C. GLBP

D. CARP

Answer: A


New Questions 18

When troubleshooting client DNS issues, which two tasks must you perform? (Choose two.)

A. Ping a public website IP address.

B. Determine whether a DHCP address has been assigned.

C. Determine whether the hardware address is correct.

D. Ping the DNS server.

E. Determine whether the name servers have been configured.

Answer: D,E


New Questions 19

What is the best way to verify that a host has a path to other hosts in different networks?

A. Ping the loopback address.

B. Ping the default gateway.

C. Ping the local interface address.

D. Ping the remote network.

Answer: D

Explanation:

Ping is a tool that helps to verify IP-level connectivity; PathPing is a tool that detects packet loss over multiple-hop trips. When troubleshooting, thepingcommand is used to send an ICMP Echo Request to a target host name or IP address. Use Ping whenever you want to verify that a host computer can send IP packets to a destination host. You can also use the Ping tool to isolate network hardware problems and incompatible configurations.

If you callipconfig /alland receive a response, there is no need to ping the loopback address and your own IP address u2014 Ipconfig has already done so in order to generate the report.

It is best to verify that a route exists between the local computer and a network host by first using ping and the IP address of the network host to which you want to connect. The command syntax is:

ping <IP address>

Perform the following steps when using Ping:

u2711 Ping the loopback address to verify that TCP/IP is installed and configured correctly on the local computer.

ping 127.0.0.1

If the loopback step fails, the IP stack is not responding. This might be because the TCP drivers are corrupted, the network adapter might not be working, or another service is interfering with IP.

u2711 Ping the IP address of the local computer to verify that it was added to the network

correctly. Note that if the routing table is correct, this simply forwards the packet to the loopback address of 127.0.0.1.

ping<IP address of local host>

u2711 Ping the IP address of the default gateway to verify that the default gateway is functioning and that you can communicate with a local host on the local network.

ping<IP address of default gateway>

u2711 Ping the IP address of a remote host to verify that you can communicate through a router.

ping<IP address of remote host>

u2711 Ping the host name of a remote host to verify that you can resolve a remote host name.

ping<Host name of remote host>

u2711 Run a PathPing analysis to a remote host to verify that the routers on the way to the destination are operating correctly.

pathping<IP address of remote host>


New Questions 20

Which three statements about static routing are true? (Choose three.)

A. It uses consistent route determination.

B. It is best used for small-scale deployments.

C. Routing is disrupted when links fail.

D. It requires more resources than other routing methods.

E. It is best used for large-scale deployments.

F. Routers can use update messages to reroute when links fail.

Answer: A,B,C


New Questions 21

Which network topology allows all traffic to flow through a central hub?

A. bus

B. star

C. mesh

D. ring

Answer: B


New Questions 22

What is the default lease time for a DHCP binding?

A. 24 hours

B. 12 hours

C. 48 hours

D. 36 hours

Answer: A

Explanation: By default, each IP address assigned by a DHCP Server comes with a one- day lease, which is the amount of time that the address is valid. To change the lease value for an IP address, use the following command in DHCP pool configuration mode:


New Questions 23

Which type of address is the public IP address of a NAT device?

A. outside global

B. outside local

C. inside global

D. inside local

E. outside public

F. inside public

Answer: C


Recommend!! Get the Download 200-125 dumps in VCE and PDF From Examcollectionplus, Welcome to download: https://www.examcollectionplus.net/vce-200-125/ (New 889 Q&As Version)