Proper study guides for Most recent Cisco CCNA Cisco Certified Network Associate CCNA (v3.0) certified begins with Cisco ccna routing and switching 200 125 preparation products which designed to deliver the Highest Quality 200 125 cisco questions by making you pass the ccna 200 125 study guide test at your first time. Try the free 200 125 ccna book demo right now.
P.S. Highest Quality 200-125 preparation are available on Google Drive, GET MORE: https://drive.google.com/open?id=1jQmx5oxI6Dh5yoCIPQpEra2L4K5UYNUa
New Cisco 200-125 Exam Dumps Collection (Question 9 - Question 18)
Question No: 9
Which two statements about IPv6 and routing protocols are true? (Choose two.)
A. Link-local addresses are used to form routing adjacencies.
B. OSPFv3 was developed to support IPv6 routing.
C. EIGRP, OSPF, and BGP are the only routing protocols that support IPv6.
D. Loopback addresses are used to form routing adjacencies.
E. EIGRPv3 was developed to support IPv6 routing.
Answer: A,B
Question No: 10
When enabled, which feature prevents routing protocols from sending hello messages on an interface'?
A. virtual links
B. passive-interface
C. directed neighbors
D. OSPF areas
Answer: B
Explanation:
You can use thepassive-interfacecommand in order to control the advertisement of routing information. The command enables the suppression of routing updates over some interfaces while it allows updates to be exchanged normally over other interfaces.
With most routing protocols, thepassive-interfacecommand restricts outgoing advertisements only. But, when used with Enhanced Interior Gateway Routing Protocol (EIGRP), the effect is slightly different. This document demonstrates that use of the passive-interfacecommand in EIGRP suppresses the exchange of hello packets between two routers, which results in the loss of their neighbor relationship. This stops not only routing updates from being advertised, but it also suppresses incoming routing updates. This document also discusses the configuration required in order to allow the suppression
of outgoing routing updates, while it also allows incoming routing updates to be learned normally from the neighbor.
Question No: 11
Which NTP command configures the local device as an NTP reference clock source?
A. ntp peer
B. ntp broadcast
C. ntp master
D. ntp server
Answer: D
Question No: 12
If primary and secondary root switches with priority 16384 both experience catastrophic losses, which tertiary switch can take over?
A. a switch with priority 20480
B. a switch with priority 8192
C. a switch with priority 4096
D. a switch with priority 12288
Answer: A
Question No: 13
If a router has four interfaces and each interface is connected to four switches, how many broadcast domains are present on the router?
A. 1
B. 2
C. 4
D. 8
Answer: C
Question No: 14
By default, how many MAC addresses are permitted to be learned on a switch port with port security enabled?
A. 8
B. 2
C. 1
D. 0
Answer: C
Question No: 15
Which function of the IP SLAs ICMP jitter operation can you use to determine whether a VoIP issue is caused by excessive end-to-end time?
A. packet loss
B. jitter
C. successive packet loss
D. round-trip time latency
Answer: D
Question No: 16
If all OSPF routers in a single area are configured with the same priority value, what value does a router use for the OSPF router ID in the absence of a loopback interface?
A. the IP address of the first Fast Ethernet interface
B. the IP address of the console management interface
C. the highest IP address among its active interfaces
D. the lowest IP address among its active interfaces
E. the priority value until a loopback interface is configured
Answer: C
Explanation: Ordinarily the loopback interface would be selected as the router ID. In the event that no loopback interface is configured, the router ID will be the first active interface that comes up on the router. If that particular interface has more then one IP address, then the highest address will be selected as the Router ID.
Question No: 17
Which command can you enter to configure a local username with an encrypted password and EXEC mode user privileges?
A. Router(config)#username jdone privilege 1 password 7 08314D5D1A48
B. Router(config)#username jdone privilege 1 password 7 PASSWORD1
C. Router(config)#username jdone privilege 15 password 0 08314D5D1A48
D. Router(config)#username jdone privilege 15 password 0 PASSWORD1
Answer: A
Question No: 18
Which IEEE standard does PVST+ use to tunnel information?
A. 802.1x
B. 802 1q
C. 802.1w
D. 802.1s
Answer: B
100% Most recent Cisco 200-125 Questions & Answers shared by 2passeasy, Get HERE: https://www.2passeasy.com/dumps/200-125/ (New 889 Q&As)