Master the 200 125 ccna pdf CCNA Cisco Certified Network Associate CCNA (v3.0) content and be ready for exam day success quickly with this Certleader 200 125 ccna v3 0 sample question. We guarantee it!We make it a reality and give you real ccna 200 125 study guide questions in our Cisco cisco ccna 200 125 braindumps.Latest 100% VALID Cisco ccna 200 120 vs 200 125 Exam Questions Dumps at below page. You can use our Cisco 200 125 ccna v3 0 braindumps and pass your exam.

P.S. Highest Quality 200-125 discount pack are available on Google Drive, GET MORE: https://www.slideshare.net/reinigerodp/certleader-200-125examquestionsmaterials


New Cisco 200-125 Exam Dumps Collection (Question 15 - Question 24)

Q15. Which routing protocol has the smallest default administrative distance?

A. IBGP

B. OSPF

C. IS-IS

D. EIGRP

E. RIP

Answer: D

Explanation: http://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol- bgp/15986-admin-distance.html

Default Distance Value Table

This table lists the administrative distance default values of the protocols that Cisco supports:

Route Source

Default Distance Values

Connected interface 0

Static route 1

Enhanced Interior Gateway Routing Protocol (EIGRP) summary route 5

External Border Gateway Protocol (BGP) 20

Internal EIGRP 90

IGRP 100 OSPF

110

Intermediate System-to-Intermediate System (IS-IS) 115

Routing Information Protocol (RIP) 120

Exterior Gateway Protocol (EGP) 140

On Demand Routing (ODR) 160

External EIGRP 170

Internal BGP 200

Unknown* 255


Q16. Which protocol advertises a virtual IP address to facilitate transparent failover of a Cisco routing device?

A. FHRP

B. DHCP

C. RSMLT

D. ESRP

Answer: A


Q17. What are two benefits of private IPv4 IP addresses? (Choose two.)

A. They are routed the same as public IP addresses.

B. They are less costly than public IP addresses.

C. They can be assigned to devices without Internet connections.

D. They eliminate the necessity for NAT policies.

E. They eliminate duplicate IP conflicts.

Answer: B,C


Q18. Which statement about switch access ports is true?

A. They drop packets with 802.1Q tags.

B. A VLAN must be assigned to an access port before it is created.

C. They can receive traffic from more than one VLAN with no voice support

D. By default, they carry traffic for VLAN 10.

Answer: A

Explanation:

"If an access port receives a packet with an 802.1Q tag in the header other than the access VLAN value, that port drops the packet without learning its MAC source address."


Q19. Why did Branch1 router lose WAN connectivity with R1 router?

A. The IP address is misconfigured on PPP multilink interface on the Branch1 router.

B. The PPP multilink group is misconfigured on the u00a3ranch1 serial interfaces.

C. The PPP multilink group is misconfigured on the R1 serial interfaces.

D. The Branch1 serial interfaces are placed in a shutdown condition.

Answer: A

Explanation: This question clearly stated there is a WAN connectivity issue between R1 and Branch1 so we should check both of them with the u201cshow ip interface briefu201d command. On R1:

On Branch1:

We can see that although the Multilink1 interfaces are in u201cup/upu201d state but they are not in the same subnet. According to the IP address scheme shown on the topology we can deduce the Multilink interface on Branch1 has been misconfigured, it should be 192.168.14.2 instead.


Q20. What is the correct routing match to reach 172.16.1.5/32?

A. 172.16.1.0/26

B. 172.16.1.0/25

C. 172.16.1.0/24

D. the default route

Answer: A


Q21. Which condition does the err-disabled status indicate on an Ethernet interface?

A. There is a duplex mismatch.

B. The device at the other end of the connection is powered off.

C. The serial interface is disabled.

D. The interface is configured with theshutdowncommand.

E. Port security has disabled the interface.

F. The interface is fully functioning.

Answer: A


Q22. Which feature can you implement to reserve bandwidth for VoIP calls across the call path?

A. PQ

B. CBWFQ

C. round robin

D. RSVP

Answer: D


Q23. Refer to the exhibit.

What is the result of setting the no login command?

A. Telnet access is denied.

B. Telnet access requires a new password at the first login.

C. Telnet access requires a new password.

D. no password is required for telnet access.

Answer: D


Q24. How can you disable DTP on a switch port?

A. Configure the switch port as a trunk.

B. Add an interface on the switch to a channel group.

C. Change the operational mode to static access.

D. Change the administrative mode to access.

Answer: A