Testking possesses good quality products which are usually refreshed up to date capture up with the genuine assessment. Prospects who take advantage of Testking checks will definitely go the actual Cisco 200-125 assessment. Simply by visiting the actual Contact Us and also Are living Chitchat page, you receive the online service. You may also correspond with these people every once in awhile and examine the actual The item technological innovation jointly. Testking makes sure that you go the actual Cisco 200-125 assessment effortlessly. Anyone who does not go gets back all order service fees regarding Testking perform checks by providing the actual proof the actual unsuccessful assessment. Can you nonetheless doubtfulness about the proficiency for Testking Cisco 200-125 assessment and 200-125? To remove your very last fret when shopping from Testking, they offer No cost Demo Demo. In this manner, you may make wise course of action dependant upon your very own judgment and not everything we declare.
2021 Sep 200-125 free practice exam
Q11. - (Topic 4)
Refer to the graphic.
R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.)
A. All of the routers need to be configured for backbone Area 1.
B. R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
C. A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
D. The hello and dead interval timers are not set to the same values on R1 and R3.
E. EIGRP is also configured on these routers with a lower administrative distance.
F. R1 and R3 are configured in different areas.
Answer: D,F
Q12. - (Topic 3)
Refer to the exhibit.
What is the most efficient summarization that R1 can use to advertise its networks to R2?
A. 172.1.0.0/22
B. 172.1.0.0/21
C. 172.1.4.0/22
D. 172.1.4.0/24
172.1.5.0/24
172.1.6.0/24
172.1.7.0/24
E. 172.1.4.0/25
172.1.4.128/25
172.1.5.0/24
172.1.6.0/24
172.1.7.0/24
Answer: C
Q13. - (Topic 9)
Which three statements about link-state routing are true? (Choose three.)
A. Routes are updated when a change in topology occurs.
B. Updates are sent to a multicast address by default.
C. OSPF is a link-state protocol.
D. Updates are sent to a broadcast address.
E. RIP is a link-state protocol.
F. It uses split horizon.
Answer: A,B,C
Q14. - (Topic 2)
Refer to the exhibit.
At the end of an RSTP election process, which access layer switch port will assume the discarding role?
A. Switch3, port fa0/1
B. Switch3, port fa0/12
C. Switch4, port fa0/11
D. Switch4, port fa0/2
E. Switch3, port Gi0/1
F. Switch3, port Gi0/2
Answer: C
Q15. - (Topic 4)
Which parameter or parameters are used to calculate OSPF cost in Cisco routers?
A. Bandwidth
B. Bandwidth and Delay
C. Bandwidth, Delay, and MTU
D. Bandwidth, MTU, Reliability, Delay, and Load
Answer: A
Down to date 200-125 practice:
Q16. - (Topic 4)
What is the default maximum number of equal-cost paths that can be placed into the routing table of a Cisco OSPF router?
A. 2
B. 8
C. 16
D. unlimited
Answer: B
Q17. - (Topic 3)
Which IPv6 address is the all-router multicast group?
A. FF02::1
B. FF02::2
C. FF02::3
D. FF02::4
Answer: B
Q18. - (Topic 4)
Refer to the exhibit.
Which of these statements correctly describes the state of the switch once the boot process has been completed?
A. As FastEthernet0/12 will be the last to come up, it will be blocked by STP.
B. Remote access management of this switch will not be possible without configuration change.
C. More VLANs will need to be created for this switch.
D. The switch will need a different IOS code in order to support VLANs and STP.
Answer: B
Q19. - (Topic 3)
What is the alternative notation for the IPv6 address B514:82C3:0000:0000:0029:EC7A:0000:EC72?
A. B514 : 82C3 : 0029 : EC7A : EC72
B. B514 : 82C3 :: 0029 : EC7A : EC72
C. B514 : 82C3 : 0029 :: EC7A : 0000 : EC72
D. B514 : 82C3 :: 0029 : EC7A : 0 : EC72
Answer: D
Q20. DRAG DROP - (Topic 7)
Answer: