The Only Tip You Need: 300 075 dump

Question No: 1

Which command should you use on the gatekeeper to specify the address of a Cisco Unified Communications Manager IP address?

A. gw-type-ip

B. gw-type-prefix-ip

C. gw-ip-cm

D. gw-type-prefix

E. gw-ip-type

F. gw-prefix-ip

Question No: 2

Which method can be used to address variable-length dial plans?

A. Overlap sending and receiving.

B. Add a prefix for all calls that are longer than 10-digits long

C. Use nested translation patterns to eliminate inter-digit timeout

D. Use the @macro on the route pattern

E. Use MGCP gateways, which support variable-length dial plans

Question No: 3

Which Cisco IOS command is used to verify that a SAF Forwarder that is registered with Cisco Unified Communications Manager has established neighbor relations with an adjacent SAF Forwarder?

A. show eigrp service-family ipv4 neighbors

B. show eigrp address-family ipv4 neighbors

C. show voice saf dndball

D. show saf neighbors

E. show ip saf neighbors

Question No: 4

During device failover to the secondary Cisco Unified Communications Manager server, how does the phone recognize that the primary server is back?

A. The secondary server keeps sending keepalive message to the primary server and when it succeeds, it unregisters the phones to force them to register to the primary.

B. When the primary server goes online, it sends out an "ALIVE" message via broadcast so that the phones re-register.

C. The phones never re-register with the primary server until the active (secondary) one goes down.

D. The phone sends keepalive messages to the primary server frequently and when it succeeds, the phone re-registers with it.

Question No: 5

Which option describes a function of SIP preconditions?

A. SIP preconditions enable end-to-end RSVP over an SIP trunk.

B. SIP preconditions enable RSVP between Cisco IP Phones.

C. SIP preconditions can be enabled in a gatekeeper.

D. SIP preconditions enable end-to-end RSVP for calls through the PSTN.

Question No: 6

Refer to the exhibit.

All HQ phones are configured to use HQ_MRGL and all BR phones are configured to use BR_MRGL. For the HQ phones always to use the hardware conference bridge as a first choice, which configuration should be implemented?

A. Ensure that both the hardware and software conference bridges are listed in the HQ_MRG. Ensure that the instance ID for the hardware conference bridge is 0.

B. Ensure that both the hardware and software conference bridges are listed in the HQ_MRG. The hardware conference bridge must be configured first.

C. Assign the hardware conference bridge to HQ_MRG. Configure a second HQ_MRG_2 and assign the software conference bridge to it. Add both the HQ_MRG and HQ_MRG_2 to the HQ_MRGL and list the HQ_MRG first.

D. Assign the hardware conference bridge to HQ_MRG. Configure a second HQ_MRG_2 and assign the software conference bridge to it. Configure an additional HQ_MRGL_2. Add the HQ_MRG to HQ_MRGL. Add HQ_MRG_2 to HQ_MRGL_2. The HQ_MRGL should be assigned to the HQ phones. The HQ_MRGL_2 should be assigned to the HQ device pool.

Question No: 7

Refer to the exhibit.

The Cisco Unified Communications Manager at HQ has been configured for end-to-end RSVP. The Cisco Unified Communications Manager at BR has been configured for local RSVP.

RSVP between the locations assigned to the IP phones and SIP trunks at each site are configured with mandatory RSVP. When a call is placed from the IP phone at the BR site to the IP phone at the HQ site, which statement is true?

A. The Cisco Unified Communications Manager at BR will fall back to local RSVP and place the call. No RSVP end-to-end will occur.

B. RSVP end-to-end will occur.

C. The Cisco Unified Communications Manager at BR will use local RSVP. The HQ Cisco Unified Communications Manager will use end-to-end RSVP.

D. The call will fail.

E. The call will proceed as a normal call with no RSVP reservation.

Question No: 8

When you configure regions in a Cisco Unified Communications Manager multisite cluster, which two are ways to prevent G.722 from being advertised in the cluster? (Choose two.)

A. modify the service parameter

B. modify the enterprise parameter

C. modify the device pool

D. modify the line settings

Question No: 9

Which interface can you use to configure alarms and traces in Cisco Unified

Communications Manager?

A. Cisco Unified Reporting

B. Cisco Unified Serviceability

C. Cisco Unified Communications Manager Administration

D. disaster recovery system

E. Cisco Unified OS Administration

F. real-time monitoring

Question No: 10

When Cisco Extension Mobility is implemented, how is the audio source for the MOH selected?

A. The audio source that is configured at the user device profile is selected.

B. The audio source that is configured at the home phone of the user is selected.

C. The audio source that is configured at the physical phone used for the Cisco Extension Mobility login is selected.

D. The audio source that is configured in the IP Voice Media Streaming parameters is selected.