It is impossible to pass Cisco 300-080 exam without any help in the short term. Come to us soon and find the most advanced, correct and guaranteed 300-080 Exam Questions and Answers. You will get a surprising result by our 300-080 Free Practice Questions.

Online Cisco 300-080 free dumps demo Below:

NEW QUESTION 1
Upon completion of a failover task you notice that all the CTI devices are still pointing to the backup server rather than the primary server. How should you resolve this issue?

  • A. Stop the CTI Manager Service on the Secondary server so that all devices using CTI register with the primary.
  • B. Stop the CTI Manager Service on the Primary server so that all devices using CTI stay registered with the primary CTI server.
  • C. Restart the subscriber with the CTI Manager Service on the secondary.
  • D. Do nothing and wait for the next failover assuming this will revert back to the primary CTI server.

Answer: A

NEW QUESTION 2
Refer to the exhibit.
300-080 dumps exhibit
You are trying to establish a multipoint call via a Cisco TelePresence SX20 that is registered to Cisco Unified Communications Manager. When you attempt to bring a third party into the call, you receive an error that the call cannot be completed. You confirm that your MCU resources are configured correctly on Cisco Unified Communications Manager and that other devices are able to establish multipoint calls. What is the cause of this issue?

  • A. The multipoint mode should be set to Multiway.
  • B. The call protocol should be H.323.
  • C. The MCU is at capacity.
  • D. The multipoint mode should be set to Cisco Unified Communications Manager Resource Group.
  • E. The multipoint mode should be set to None.

Answer: D

NEW QUESTION 3
A user gets the following error on the IP phone: [205]-User Profile Absent
What could be the probable cause?

  • A. The user profile is missing.
  • B. The device profile is not attached to the user.
  • C. The Enable Extension Mobility option is not enabled in the phone configuration window.
  • D. User ID and password are incorrectly entered on the phone.
  • E. User is assigned to another phone.
  • F. User is logged on to another phone.

Answer: B

NEW QUESTION 4
What is the meaning of this alarm snippet
CCM_CALLMANAGER-CALLMANAGER-3-EndPointTfansientConnection?

  • A. The device was successfully unregistered.
  • B. The device was reset via the reset button in Cisco Unified Communications Manager.
  • C. The device was misconfigured.
  • D. The device was successfully registered.

Answer: C

NEW QUESTION 5
Which statement indicates something that can cause an inbound PSTN call to an H.323 gateway that is configured in Cisco Unified Communications Manager to fail to ring an IP phone?

  • A. The gateway is not registered in Cisco Unified Communications Manager.
  • B. The gateway IP address that is configured in Cisco Unified Communications Manager does not matchthe IP address that is configured at the gateway in the h323-gateway voip bind srcaddr command.
  • C. The Cisco Unified Communications Manager does not have a matching route pattern to match the called number.
  • D. The gateway is missing the command allow-connections h323 to h323 under the voice service voip configuration.

Answer: B

NEW QUESTION 6
Refer to the exhibit.
300-080 dumps exhibit
ACustomer has two Cisco Unified Communications Manager clusters (NY and CAL). The customer recently tried to enable intercluster communication between these clusters. When NY users call CAL, they get a
fast-busy tone. A network administrator collects Cisco CallManager traces and sees the displayed SIP message coming from the remote Cisco Unified Communication Manager (CAL cluster). What is a likely reason for this?

  • A. Cisco CallManager service is shut down on the CAL cluster.
  • B. The SIP service is shut down on the CAL cluster.
  • C. The SIP trunk on the CAL cluster is configured incorrectly.
  • D. Cisco CTI Manager service is shut down on the CAL cluster.
  • E. The remote Cisco IP phone is not registered.

Answer: E

NEW QUESTION 7
Refer to the exhibit.
300-080 dumps exhibit
Inbound calls via a SIP trunk to the Cisco IP phones that are registered on Cisco Unified Communications Manager are failing. Based on the Cisco CallManager service trace, which action should you take to fix the issue?

  • A. Add xyz.com in the Organization Top Level Domain field on Cisco Unified Communications Manager.
  • B. Set the Incoming Transport Type to TLS on the SIP trunk security profile that is assigned to the SIP trunk.
  • C. Check whether the calling search space for incoming calls on the SIP trunk has access to the partition ofthe Cisco IP phone that is being called.
  • D. Add vcs.abc.org in the Organization Top Level Domain field on Cisco Unified Communications Manager.

Answer: C

NEW QUESTION 8
What is the default interval for SAF hello packets?

  • A. 15 seconds
  • B. 15 seconds on links with speeds that are slower than T1 speeds
  • C. 40 seconds
  • D. 40 seconds on links with speeds that are slower than T1 speeds
  • E. 60 seconds
  • F. 60 seconds on links with speeds that are slower than T1 speeds

Answer: F

NEW QUESTION 9
Refer to the exhibit.
300-080 dumps exhibit
Which course of action will resolve the Mobile Connect issues that are shown in the exhibit?

  • A. Configure the Mobility softkey on the phone.
  • B. Enable the user for Cisco Mobile Connect.
  • C. Make the user an owner of the phone device in the phone device configuration page.
  • D. Enable the device mobility mode on the phone since it is disabled.

Answer: C

NEW QUESTION 10
A user takes an IP phone from one office to another and just called you to inform that the phone does not work in the new location. Which three things should you check to resolve the issue? (Choose three)

  • A. Make sure that the device mobility information contains the correct IP subnet information.
  • B. Make sure that physical locations are properly assigned under device pools.
  • C. Recreate the phone under a new cluster.
  • D. Make sure that the device pool is assigned to a device mobility group.
  • E. Reconfigure the remote destination profile.
  • F. Check whether the phone is registered under a different MAC address.
  • G. Check the local DHCP information for possible clues.

Answer: ABG

NEW QUESTION 11
In a single-site deployment model, the internal endpoints are unable to dial from one to the other. What are two possible causes? (Choose two.)

  • A. The PSTN gateway is not configured.
  • B. The calleDEndpoint does not have the SIP trunk enabled.
  • C. The calleDEndpoint is not registered.
  • D. The calling endpoint is not in the CSS of the calleDEndpoint.
  • E. The calleDEndpoint is not in the partition of the calling endpoint.
  • F. The calling endpoint is not configureDFor the correct CoS.

Answer: CF

NEW QUESTION 12
Refer to the exhibit.
300-080 dumps exhibit
A new phone was installed and currently has issues registering with Cisco Unified Communications Manager. The phone received its IP address via DHCP, with options 3 and 150.
Which two actions woulDEnable the phone to download its configuration automatically? (Choose two.)

  • A. Change the phone URL parameters to IP addresses.
  • B. Provide DHCP option 6 to the phone via DHCP.
  • C. Reboot the phone.
  • D. Change the VLAN that the phone is assigned to.
  • E. Manually assign the phone settings.
  • F. Provide DHCP option 15 to the phone via DHCP.

Answer: AB

NEW QUESTION 13
When dialing any external SIP URI for ABusiness-to-business call, an endpoint that is registered to the Cisco VCS Control fails to locate the remote endpoint. The same endpoint can successfully call another endpoint that is registered to the Cisco VCS Expressway. How do you resolve this issue?

  • A. Add traversal call licensing on the Cisco VCS Expressway.
  • B. Add traversal call licensing on the Cisco VCS Control.
  • C. Add a multisite option to the endpoint.
  • D. Configure a proper DNS zone on the Cisco VCS Expressway.
  • E. Configure a traversal zone between the Cisco VCS Control and the Cisco VCS Expressway.
  • F. Configure a SIP route pattern in Cisco Unified Communications Manager.

Answer: D

NEW QUESTION 14
A network administrator is troubleshooting a support ticket with ID33118456 regarding video bandwidth issues. On a Cisco TelePresence VCS, the administrator can configure bandwidth control for which two VCS configuration options? (Choose two)

  • A. links and pipes
  • B. subzones
  • C. CPL
  • D. Bandwidth restrictions can be configured only on endpoints.
  • E. zones

Answer: AB

NEW QUESTION 15
Refer to the exhibit.
300-080 dumps exhibit
a Cisco Unified Communications Manager engineer configured CCD in two clusters. The patterns were successfully learned, however, the call attempt from the cluster 1 agent to the cluster 2 agent fails. Based on the output of this cluster 1 trace, what is the root cause of the issue?

  • A. The CCD partition is missing from the CCD Requesting Service configuration
  • B. The CSS is missing from the phones and line configuration
  • C. The Activated Feature check in the CCD Requesting Service configuration is missing
  • D. The pattern that was dialed has been added to the Blocked Learned Pattern configuration

Answer: B

NEW QUESTION 16
Refer to the exhibit.
300-080 dumps exhibit
How many high-complexity transcoding sessions can this Cisco ISR G2 support?

  • A. 21
  • B. 14
  • C. 60
  • D. 15

Answer: B

NEW QUESTION 17
While you deploy SAF CCD in a remote location, you are unable to enable the SAF CCD service on an Cisco IOS-based device. Which action can you take to troubleshoot the problem?

  • A. Verify that Cisco Unity Express is operational.
  • B. Verify that IOS Release 15.0(1)M is installed.
  • C. Verify that DSP Farm resources are configured on the device.
  • D. Verify that the device has sufficient RAM to run SAF CCD.
  • E. Verify the integrity of the flash installation.

Answer: A

NEW QUESTION 18
Of the following persistent settings for Cisco TMS-controlleDEndpoints, TMS overwrites these settings if which five of them are altered on the endpoint? (Choose five.)

  • A. H.323 ID
  • B. Configuration Template
  • C. SIP URI
  • D. Active Cisco Unified Communications Manager Address
  • E. System Name
  • F. System Contact
  • G. E.164 alias
  • H. IEEE 802.1x Authentication Password

Answer: ABCEG

P.S. DumpSolutions now are offering 100% pass ensure 300-080 dumps! All 300-080 exam questions have been updated with correct answers: https://www.dumpsolutions.com/300-080-dumps/ (219 New Questions)