Your success in Cisco ccnp routing and switching route 300 101 is our sole target and we develop all our ccnp 300 101 pdf braindumps in a way that facilitates the attainment of this target. Not only is our 300 101 route study material the best you can find, it is also the most detailed and the most updated. ccnp 300 101 Practice Exams for Cisco CCDP ccnp route 300 101 are written to the highest standards of technical accuracy.

P.S. Download 300-101 faq are available on Google Drive, GET MORE: https://drive.google.com/open?id=1oF6hAYEiseB3LPIXYA2sgTXv0r2MX46d


New Cisco 300-101 Exam Dumps Collection (Question 11 - Question 20)

New Questions 11

Refer to exhibit.

What is indicated by the show ip cef command for an address?

A. CEF is unable to get routing information for this route.

B. CEF cannot switch packet for this route and passes it to the next best switching method.

C. A valid entry and is pointed to hardware based forwarding.

D. CEF cannot switch packet for this route and drops it.

Answer: B

Explanation: Glean adjacency u2013 in short when the router is directly connected to hosts the FIB table on the router will maintain a prefix for the subnet rather than for the individual host prefix. This subnet prefix points to a GLEAN adjacency.

Punt adjacency u2013 When packets to a destination prefix canu2021t be CEF Switched, or the feature is not supported in the CEF Switching path, the router will then use the next slower switching mechanism configured on the router.


New Questions 12

A network engineer is trying to modify an existing active NAT configuration on an IOS router by using the following command:

(config)# no ip nat pool dynamic-nat-pool 192.1.1.20 192.1.1.254 netmask 255.255.255.0 Upon entering the command on the IOS router, the following message is seen on the

console:

%Dynamic Mapping in Use, Cannot remove message or the %Pool outpool in use, cannot destroy

What is the least impactful method that the engineer can use to modify the existing IP NAT configuration?

A. Clear the IP NAT translations using the clear ip nat traffic * " command, then replace the NAT configuration quickly, before any new NAT entries are populated into the translation table due to active NAT traffic.

B. Clear the IP NAT translations using the clear ip nat translation * " command, then replace the NAT configuration quickly, before any new NAT entries are populated into the translation table due to active NAT traffic.

C. Clear the IP NAT translations using the reload command on the router, then replace the NAT configuration quickly, before any new NAT entries are populated into the translation table due to active NAT traffic.

D. Clear the IP NAT translations using the clear ip nat table * " command, then replace the NAT configuration quickly, before any new NAT entries are populated into the translation table due to active NAT traffic.

Answer: B


New Questions 13

Which type of address does OSPFv3 use to form neighbor adjacencies and to send LSAs?

A. unicast IPv6 addresses

B. link-local addresses

C. multicast address FF02::5

D. unicast IPv4 addresses

Answer: C


New Questions 14

Refer to following:

router eigrp 1

redistribute ospf 1 route-map ospf-to-eigrp default-metric 20000 2000 255 1 1500

!

route-map ospf-to-eigrp deny 10 match tag 6

match route-type external type-2

!

route-map ospf-to-eigrp permit 20 match ip address prefix-list pfx

set metric 40000 1000 255 1 1500

!

route-map ospf-to-eigrp permit 30 set tag 8

Which three statements accurately describe the result of applying the exhibited route map?

A. The map prohibits the redistribution of all type 2 external OSPF routes with tag 6 set.

B. The map prohibits the redistribution of all type 2 external OSPF routes.

C. The map redistributes into EIGRP all routes that match the pfx prefix list and the five metric values 40000, 1000, 255, 1, and 1500.

D. The map prohibits the redistribution of all external OSPF routes with tag 6 set.

E. All routes that do no match clauses 10 and 20 of the route map are redistributed with their tags set to 8.

F. The map permits the redistribution of all type 1 external OSPF routes.

Answer: A,E,F


New Questions 15

A network engineer is troubleshooting connectivity issues with a directly connected RIPng neighbor. Which command should directly connected RIPng neighbor adjacencies only?

A. router#show ipv6 rip next-hops

B. router#show ip rip neighbors

C. router#show ipv6 routers

D. router#show ipv6 rip database

Answer: A


New Questions 16

A network engineer is disabling split horizon on a point-to-multipoint interface that is running RIPng. Under which configuration mode can split horizon be disabled?

A. router(config-riping)#

B. router(config-rtr)#

C. router(config-if)#

D. router(config)#

Answer: D


New Questions 17

An organization decides to implement NetFlow on its network to monitor the fluctuation of traffic that is disrupting core services. After reviewing the output of NetFlow, the network engineer is unable to see OUT traffic on the interfaces. What can you determine based on this information?

A. Cisco Express Forwarding has not been configured globally.

B. NetFlow output has been filtered by default.

C. Flow Export version 9 is in use.

D. The command ip flow-capture fragment-offset has been enabled.

Answer: A


New Questions 18

To configure 6to4 tunneling on a dual-stack edge router. Which three of the following are valid components in 6to4 Tunneling configuration? (Choose Three)

A. IPv4 Tunnel IP address

B. Tunnel mode (6to4)

C. Tunnel Keepalives

D. IPv4 Tunnel Destination

E. IPv4 Tunnel Source

F. 6to4 IPv6 address (within 2002::/16)

Answer: B,E,F


New Questions 19

Which three are characteristics of IPv6? (Choose three.)

A. An IPv6 address is 128 bits long.

B. An IPv6 header is 20 bits long.

C. An IPv6 header contains the next header field.

D. An IPv6 header contains the protocol field.

E. IPv6 routers send RA messages.

F. An IPv6 header contains the header checksum field.

Answer: A,C,E

Explanation:

All IPv6 addresses are 128 bits long to accommodate a far larger number of stations than what was possible with the 32 bit IPv4 addresses.

The following displays the IPv6 header field in detail: IPv6 header:

Version. 4 bits.IPv6 version number.

Traffic Class. 8 bits.Internet traffic priority delivery value.

Flow Label. 20 bits.Used for specifying special router handling from source to destination(s) for a sequence of packets.

Payload Length. 16 bits unsigned.Specifies the length of the data in the packet. When cleared to zero, the option is a hop-by-hop Jumbo payload.

Next Header. 8 bits.Specifies the next encapsulated protocol. The values are compatible with those specified for the IPv4 protocol field.

Hop Limit. 8 bits unsigned.For each router that forwards the packet, the hop limit is decremented by 1. When the hop limit field reaches zero, the packet is discarded. This replaces the TTL field in the IPv4 header that was originally intended to be used as a time based hop limit.

Source address. 16 bytes.The IPv6 address of the sending node. Destination address. 16 bytes.The IPv6 address of the destination node.


New Questions 20

Which Cisco VPN technology can use multipoint tunnel, resulting in a single GRE tunnel interface on the hub, to support multiple connections from multiple spoke devices?

A. DMVPN

B. GETVPN

C. Cisco Easy VPN

D. FlexVPN

Answer: A


Recommend!! Get the Download 300-101 dumps in VCE and PDF From Surepassexam, Welcome to download: https://www.surepassexam.com/300-101-exam-dumps.html (New 745 Q&As Version)