What Regenerate 300-135 Is?

Testking have the most accurate as well as authentic Cisco Cisco practice questions which usually with 100% proper answers. Our certified subject matter authorities are dedicated to researching as well as creating your Cisco Cisco exam dumps which contain your latest contents inside accordance with the 300-135 exam syllabus. Many of us hope you will reach your goals in Cisco Cisco 300-135 exam with the Cisco Cisco practice questions and answers. A lot of candidates have got success after acquiring our Cisco products. We are usually proud of the substantial passing ratio. However, in case you unluckily fail the Cisco certification exam, we will give a person a Entire REFUND of your buying fee or even send a person another same value product or service for no cost.

2021 Mar 300-135 exam price

Q31. - (Topic 1)

Which three features are benefits of using GRE tunnels in conjunction with IPsec for building siteto-site VPNs? (Choose three.)

A. allows dynamic routing over the tunnel

B. supports multi-protocol (non-IP) traffic over the tunnel

C. reduces IPsec headers overhead since tunnel mode is used

D. simplifies the ACL used in the crypto map

E. uses Virtual Tunnel Interface (VTI) to simplify the IPsec VPN configuration

Answer: A,B,D

Q32. - (Topic 12)

The implementations group has been using the test bed to do a ‘proof-of-concept' that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241

address.

Use the supported commands to isolated the cause of this fault and answer the following questions.

On which device is the fault condition located?

A. R1

B. R2

C. R3

D. R4

E. DSW1

F. DSW2

G. ASW1

H. ASW2

Answer: G

Explanation:

port security needs is configured on ASW1.

Q33. - (Topic 16)

The implementations group has been using the test bed to do a ‘proof-of-concept'. After several changes to the network addressing, routing schemes, a trouble ticket has been opened indicating that the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2(2026::102:1).

Use the supported commands to isolated the cause of this fault and answer the following questions.

The fault condition is related to which technology?

A. NTP

B. IPv4 OSPF Routing

C. IPv6 OSPF Routing

D. IPv4 layer 3 security

Answer: C

Explanation:

On R2, IPV6 OSPF routing, configuration is required to add ipv6 ospf 6 area 0 under interface serial 0/0/0.23

Q34. - (Topic 15)

Use the supported commands to isolated the cause of this fault and answer the following questions.

On which device is the fault condition located?

A. R1

B. R2

C. R3

D. R4

E. DSW1

F. DSW2

G. ASW1

H. ASW2

Answer: E

Explanation:

On DSW1, VALN ACL, Need to delete the VLAN access-map test1 whose action is to drop access-list 10; specifically 10.2.1.3

Topic 16, Ticket 11 : IPV6 OSPF

Topology Overview (Actual Troubleshooting lab design is for below network design)

. Client Should have IP 10.2.1.3

. EIGRP 100 is running between switch DSW1 & DSW2

. OSPF (Process ID 1) is running between R1, R2, R3, R4

. Network of OSPF is redistributed in EIGRP

. BGP 65001 is configured on R1 with Webserver cloud AS 65002

. HSRP is running between DSW1 & DSW2 Switches

The company has created the test bed shown in the layer 2 and layer 3 topology exhibits.

This network consists of four routers, two layer 3 switches and two layer 2 switches.

In the IPv4 layer 3 topology, R1, R2, R3, and R4 are running OSPF with an OSPF process number 1.

DSW1, DSW2 and R4 are running EIGRP with an AS of 10. Redistribution is enabled where necessary.

R1 is running a BGP AS with a number of 65001. This AS has an eBGP connection to AS 65002 in the ISP's network. Because the company's address space is in the private range.

R1 is also providing NAT translations between the inside (10.1.0.0/16 & 10.2.0.0/16) networks and outside (209.65.0.0/24) network.

ASW1 and ASW2 are layer 2 switches.

NTP is enabled on all devices with 209.65.200.226 serving as the master clock source.

The client workstations receive their IP address and default gateway via R4's DHCP server.

The default gateway address of 10.2.1.254 is the IP address of HSRP group 10 which is running on DSW1 and DSW2.

In the IPv6 layer 3 topology R1, R2, and R3 are running OSPFv3 with an OSPF process number 6.

DSW1, DSW2 and R4 are running RIPng process name RIP_ZONE.

The two IPv6 routing domains, OSPF 6 and RIPng are connected via GRE tunnel running over the underlying IPv4 OSPF domain. Redistrution is enabled where necessary.

Recently the implementation group has been using the test bed to do a ‘proof-of-concept' on several implementations. This involved changing the configuration on one or more of the devices. You will be presented with a series of trouble tickets related to issues introduced during these configurations.

Note: Although trouble tickets have many similar fault indications, each ticket has its own issue and solution.

Each ticket has 3 sub questions that need to be answered & topology remains same.

Question-1 Fault is found on which device,

Question-2 Fault condition is related to,

Question-3 What exact problem is seen & what needs to be done for solution

Solution

Steps need to follow as below:-

. When we check on client 1 & Client 2 desktop we are not receiving DHCP address from R4

ipconfig ----- Client will be receiving IP address 10.2.1.3

. From Client PC we can ping 10.2.1.254….

. But IP 10.2.1.3 is able to ping from R4, R3, R2, R1.

. Since the problem is R1 (2026::111:1) is not able to ping loopback of DSW1 (2026::102:1).

. Kindly check for neighbourship of routers as IPV6…. As per design below neighbourship should be present for IPV6

R1 ---R2 --- R3 --- R4--- DSW1 & DSW2 ----- Neighbourship between devices of IPV6

R2 IPV6 OSPF neighbourship is with R1

R3 IPV6 OSPF neighbourship is with R4

. As per above snapshot we cannot see IPV6 neighbourship between R2 & R3 when checked interface configuration ipv6 ospf area 0 is missing on R2 which is connected to R3

. Change required: On R2, IPV6 OSPF routing, Configuration is required to add ipv6 ospf 6 area 0 under interface serial 0/0/0.23

Improved 300-135 brain dumps:

Q35. - (Topic 1)

Which statement is true about an IPsec/GRE tunnel?

A. The GRE tunnel source and destination addresses are specified within the IPsec transform set.

B. An IPsec/GRE tunnel must use IPsec tunnel mode.

C. GRE encapsulation occurs before the IPsec encryption process.

D. Crypto map ACL is not needed to match which traffic will be protected.

Answer: C

Topic 2, Troubleshooting VTP

7. - (Topic 2)

A customer network engineer has made configuration changes that have resulted in some loss of connectivity. You have been called in to evaluate a switch network and suggest resolutions to the problems.

PC2 in VLAN 200 is unable to ping the gateway address 172.16.200.1; identify the issue.

A. VTP domain name mismatch on SW4

B. VLAN 200 not configured on SW1

C. VLAN 200 not configured on SW2

D. VLAN 200 not configured on SW4

Answer: C

Explanation:

By looking at the configuration for SW2, we see that it is missing VLAN 200, and the "switchport access vlan 200" command is missing under interface eth 0/0:

\\psf\Home\.Trash\Screen Shot 2014-10-18 at 9.56.12 PM.png

Q36. - (Topic 21)

The implementation group has been using the test bed to do an IPv6 'proof-of-concept1. After several changes to the network addressing and routing schemes, a trouble ticket has been opened indicating that the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2 (2026::102:1).

Use the supported commands to isolate the cause of this fault and answer the following question.

What is the solution to the fault condition?

A. Under the interface Tunnel34 configuration delete the tunnel mode ipv6 command.

B. Under the interface Serial0/0/0.34 configuration enter the ipv6 address 2026::34:1/122 command.

C. Under the interface Tunnel34 configuration enter the ip address unnumbered Serial0/0/0.34 command.

D. Under the interface Tunnel34 configuration delete the tunnel source Serial0/0/0.34 command and enter the tunnel source 2026::34:1/122 command.

Answer: A

Explanation:

As explained earlier, the problem is with route misconfigured tunnel modes on R3. R3 is using tunnel mode ipv6, while R4 is using the default of GRE. We need to remove the "tunnel mode ipv6" command under interface Tunnel34

Q37. - (Topic 2)

Refer to the topology.

SW1 Switch Management IP address is not pingable from SW4. What could be the issue?

A. Management VLAN not allowed in the trunk links between SW1 and SW4

B. Management VLAN not allowed in the trunk links between SW1 and SW2

C. Management VLAN not allowed in the trunk link between SW2 and SW4

D. Management VLAN ip address on SW4 is configured in wrong subnet

E. Management VLAN interface is shutdown on SW4

Answer: D

Explanation:

In the network, VLAN 300 is called the Management VLAN. Based on the configurations shown below, SW1 has VLAN 300 configured with the IP address of 192.168.10.1/24, while on SW4 VLAN 300 has an IP address of 192.168.100.4/24, which is not in the same subnet.

Q38. - (Topic 19)

Use the supported commands to isolate the cause of this fault and answer the following question.

On which device is the fault condition located?

A. R1

B. R2

C. R3

D. R4

E. DSW1

F. DSW2

G. ASW1

H. ASW2

Answer: B

Explanation:

Start to troubleshoot this by pinging the loopback IPv6 address of DSW2 (2026::102:1). This can be pinged from DSW1, R4, and R3, which leads us to believe that the issue is with R2. Going further, we can see that R2 only has an IPV6 OSPF neighbor of R1, not R3:

We can then see that OSPFv3 has not been enabled on the interface to R3:

So the problem is with R2, related to IPV6 Routing, and the fix is to enable the "ipv6 ospf 6 area 0" command under the serial 0/0/0.23 interface.

2021 Mar 300-135 exam price

Improved 300-135 brain dumps:

To see all sample questions go to: 300-135 braindumps

Related 300-135 posts: