Tested of 352-001 exams materials and dump for Cisco certification for IT candidates, Real Success Guaranteed with Updated 352-001 pdf dumps vce Materials. 100% PASS CCDE Written Exam exam Today!
Q16. Refer to the exhibit.
A service provider would like to use Ethernet OAM to detect end-to-end connectivity failures between SP-SW1 and SP-SW2. In which two of these ways can you design this solution? (Choose two.)
A. Enable Y.1731 Connectivity Fault Management on the SP switches.
B. E-LMI PDUs must be forwarded over VPLS.
C. Cisco Discovery Protocol PDUs must be forwarded over the VPLS.
D. Use upward maintenance endpoints on the SP switches.
E. Enable IEEE 802.1ag Connectivity Fault Management on the SP switches.
Answer: DE
Q17. A Tier-3 Service Provider is evolving into a Tier-2 Service Provider due to the amount of Enterprise business it is receiving. The network engineers are re-evaluating their IP/MPLS design considerations in order to support duplicate/overlapping IP addressing from their Enterprise customers within each Layer 3 VPN. Which of the following would need to be reviewed to ensure stability in their network?
A. Assigning unique Route Target ID's
B. Assigning unique Route Distinguishers
C. Assigning unique IP address space for the Enterprise NAT/Firewalls
D. Assigning unique VRF ID's to each Layer 3 VPN
Answer: B
Q18. Which three factors slow down network convergence? (Choose three.)
A. constant interface flapping
B. lack of redundant paths
C. inconsistent topology states between routers
D. transport network failing to generate LoS
E. wrong summarization in ABRs
Answer: ACD
Q19. Which mechanism should be added to a network design to identify unidirectional Spanning Tree Protocol failures through BPDU loss?
A. UDLD
B. loop guard
C. BPDU guard?
D. root guard
Answer: B
Q20. A company has these requirements for access to their wireless and wired corporate LANs using 802.1x:
. Client devices that are corporate assets and have been joined to the Active
Directory domain are allowed access.
. Personal devices must not be allowed access.
. Clients and access servers must be mutually authenticated.
Which solution meets these requirements?
A. Protected Extensible Authentication Protocol/Microsoft Challenge Handshake Authentication Protocol Version 2 with user authentication
B. Extensible Authentication Protocol-Transport Layer Security with machine authentication
C. Extensible Authentication Protocol-Transport Layer Security with user authentication
D. Protected Extensible Authentication Protocol/Microsoft Challenge Handshake Authentication Protocol Version 2 with machine authentication
Answer: B
Q21. In which two ways is IPv4 and IPv6 traffic handled in a network design that uses QoS deployment options? (Choose two.)
A. IPv6 and IPv4 traffic is treated in the same way by using a single QoS policy that classifies and matches on both protocols.
B. IPv6 traffic is treated differently than IPv4 by using the flow-label field, which is built into the IPv6 packet header.
C. IPv6 traffic does not require QoS because it uses to the flow-label field, which classifies and matches on the IPv6 protocol.
D. IPv6 traffic is treated differently than IPv4 by using two different QoS policies.
E. IPv6 traffic is treated differently than IPv4 because it uses only the DSCP value and not the IP precedence.
Answer: AD
Q22. You are designing a core MPLS-based network with a single OSPF area with no external routes. Which two mechanisms can be used to improve convergence time during a failure? (Choose two.)
A. incremental SPF
B. route filtering
C. graceful restart
D. BFD
Answer: AD
Q23. A senior network designer suggests that you should improve network convergence times by reducing BGP timers between your CE router and the PE router of the service provider. Which three factors should you to consider when you adjust the timer values? (Choose three.)
A. access bandwidth
B. service provider agreement to support tuned timers
C. number of routes on the CE router
D. number of VRFs on the PE router
E. service provider scheduling of changes to the PE
Answer: ABC
Q24. Refer to the exhibit.
An enterprise is migrating its single-area OSPF network from a Frame Relay WAN service to an MPLS L3VPN service. Frame Relay will remain in only a few sites that require increased resiliency via two different WAN connections.
Which feature could be used in the ?MPLS VPN service provider network to support the design requirement by ensuring that during normal operation, intersite traffic will only use the MPLS VPN service and not the old Frame Relay service?
A. virtual links
B. sham links
C. multiple stub areas
D. super backbone
Answer: B
Q25. Refer to the exhibit.
In the DWDM network, a ring topology carries multiple services between two sites. Which option describes the employed protection design?
A. Y-cable protection
B. Splitter protection
C. Client protection
D. UDLD
E. FEC protection
Answer: C
Q26. When you design a network, when would it be required to leak routes into a Level 1 area?
A. when a multicast RP is configured in the nonbackbone area
B. when MPLS L3VPN PE devices are configured in the Level 1 areas
C. when equal cost load balancing is required between the backbone and nonbackbone areas
D. when unequal cost load balancing is required between the backbone and nonbackbone areas
Answer: B
Q27. A service provider creates a network design that runs MPLS in its WAN backbone using OSPF as the IGP routing protocol. What would be two effects of additionally implementing MPLS-TE? (Choose two.)
A. MPLS-TE is required to reroute traffic within less than 1 second in case of a link failure inside the backbone.
B. MPLS-TE is required to route different MPLS QoS service classes through different paths.
C. MPLS-TE and OSPF cannot be used together inside one MPLS network.
D. MPLS-TE cannot use OSPF for the traffic path calculation.
E. MPLS-TE is required to create backup paths independently from the IGP.
Answer: B,E
Q28. You are hired to design a solution that will improve network availability for users on a campus network with routed access. If the budget limits you to three components, which three components would you recommend in your design proposal? (Choose three.)
A. redundant power supplies in the access routers
B. standby route processors for SSO in the core routers
C. standby route processors for SSO in the distribution routers
D. standby route processors for SSO in the access routers
E. replace copper links between devices with fiber links
Answer: ADE
Q29. As part of the security protocol for your network design, you have designated that option 82 is enabled for DHCP snooping. When option 82 is enabled, which information will be added to the DHCP request?
A. switch MAC address and VLAN, module, and port
B. remote ID and circuit ID
C. switch IP address and VLAN, module, and port
D. switch MAC address and switch IP address
Answer: A
Q30. When developing an MVPN design, which performance and scalability consideration must be taken into account?
A. CE end-to-end PIM adjacency establishment
B. multicast data sent to all PE routers on the default MDT
C. RP placement in the multicast VRF
D. RP placement in the customer network
Answer: B