Q31. Which two describe the correct requirements for non-disruptive IOS ISSU on Cisco Nexus 7000 Series Switches? (Choose two.)
A. updated kickstart and system images must be staged in bootflash on single-supervisor switches
B. updated kickstart and system images must be staged in bootflash on dual-supervisor switches
C. low version skew
D. dual supervisors
E. clock synchronization
Answer: CD
Q32. You receive an error attempting to enable the vPC feature on a Cisco Nexus 7018 Switch. Which Cisco Fabric Services distribution must be operational before the feature can be enabled?
A. CFSoFC
B. CFSoIP
C. CFSoV
D. CFSoE
E. CFSoM
Answer: D
Q33. Refer to the exhibit.
A customer is having a problem getting NPV to work. What is causing the problem?
A. The core NPV switch port is not an F port.
B. The core NPV switch port is in a shutdown state.
C. The core NPV switch port is not configured on both ends.
D. The core NPV switch port is not configured on the other end.
E. The core NPV switch ports are in the wrong domain.
Answer: A
Q34. Which statement is true regarding how OTV edge devices will react based on the configuration of the VLANs being extended across the overlay network?
A. Any VLANs not extended will not be populated in the local OTV route table.
B. Only the same-site edge AED device controls which VLANs are to be extended.
C. Any extended VLANs will not be populated in the remote OTV route table.
D. By default, all VLANs on an edge device will be extended.
Answer: A
Q35. When a directly connected host pings a switch virtual interface on the Cisco Nexus 7000 Series Switch, there is intermittent ping loss. What is the cause?
A. CoPP is applying microflow policing to all traffic from the host that is destined to the CPU.
B. CoPP is applying microflow policing to all traffic to the host that is leaving the CPU.
C. CoPP is rate-limiting all ICMP traffic that is destined to the CPU.
D. CoPP is rate-limiting all ICMP traffic that is leaving the CPU.
Answer: C
Q36. Refer to the exhibit.
When suspending or deleting VSANs, which three statements are true? (Choose three.)
A. You can delete only one VSAN at a time.
B. You must wait 60 seconds after you enter the vsan suspend command before you enter another command.
C. You must wait 120 seconds after you enter the vsan suspend command before you enter another command.
D. You can unsuspend only one VSAN at a time.
E. You can delete multiple VSANs as long as they are in the same domain.
F. You can delete multiple VSANs as long as they are in the same zone.
Answer: ABD
Q37. Which command is used to check for potential vPC configuration consistency problems?
A. show vpc brief interface
B. show vpc global config
C. show vpc consistency-parameters global
D. show vpc config
Answer: C
Q38. Which command would you use to find the AED of an extended VLAN in a dual-homed site of an OTV network?
A. show otv aed on the AED
B. show otv site on any edge devices in the site
C. show otv vlan on the AED
D. show otv aed on any edge devices in the site
E. show otv vlan on any edge devices in the site
Answer: C
Q39. When configuring LLDP on Cisco Nexus 5548 Switch, what is the purpose of LLDP hold time global configuration command?
A. LLDP holdtime option is to set the length of time in milliseconds that a device should save LLDP information received before discarding it
B. LLDP holdtime option is to set the length of time in seconds that a device should save LLDP information received before discarding it
C. LLDP holdtime option to is the length of time in milliseconds to wait before performing LLDP initialization on any interface
D. LLDP holdtime option to is the length of time in seconds to wait before performing LLDP initialization on any interface
Answer: B
Q40. Which statement would explain why the overlay interface on an OTV edge device is not in the up state?
A. The site identifiers are identical within a multihomed site.
B. Multicast groups are not mapped to a range of SSM addresses to carry the multicast traffic.
C. An adjacency server is not configured for connectivity over a multicast transport.
D. The OTV IS-IS metrics do not match across all adjacent OTV edge devices.
Answer: B