It is more faster and easier to pass the Cisco 100-105 exam by using Real Cisco Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) questuins and answers. Immediate access to the Update 100-105 Exam and find the same core area 100-105 questions with professionally verified answers, then PASS your exam with a high score now.
2021 Mar 100-105 test preparation
Q91. - (Topic 2)
A switch receives a frame on one of its ports. There is no entry in the MAC address table for the destination MAC address. What will the switch do with the frame?
A. drop the frame
B. forward it out of all ports except the one that received it
C. forward it out of all ports
D. store it until it learns the correct port
Answer: B
Explanation:
Understanding this concept is prime for understanding that when switch receives the data frame from the host not having the MAC address already in the MAC table, it will add the MAC address to the source port on the MAC address table and sends the data frame. If the switch already has the MAC address in its table for the destination, it will forward the frame directly to the destination port. If it was not already in its MAC table, then they frame would have been flooded out all ports except for the port that it came from.
Q92. - (Topic 4)
What does the "Inside Global" address represent in the configuration of NAT?
A. the summarized address for all of the internal subnetted addresses
B. the MAC address of the router used by inside hosts to connect to the Internet
C. a globally unique, private IP address assigned to a host on the inside network
D. a registered address that represents an inside host to an outside network
Answer: D
Explanation:
NAT: Local and Global Definitions http://www.cisco.com/en/US/tech/tk648/tk361/technologies_tech_note09186a0080094837. shtml Cisco defines these terms as: Inside local address—The IP address assigned to a host on the inside network. This is the address configured as a parameter of the computer OS or received via dynamic address allocation protocols such as DHCP. The address is likely not a legitimate IP address assigned by the Network Information Center (NIC) or service provider. Inside global address—A legitimate IP address assigned by the NIC or service provider that represents one or more inside local IP addresses to the outside world. Outside local address—The IP address of an outside host as it appears to the inside network. Not necessarily a legitimate address, it is allocated from an address space routable on the inside. Outside global address—The IP address assigned to a host on the outside network by the host owner. The address is allocated from a globally routable address or network space. These definitions still leave a lot to be interpreted. For this example, this document redefines these terms by first defining local address and global address. Keep in mind that the terms inside and outside are NAT definitions. Interfaces on a NAT router are defined as inside or outside with the NAT configuration commands, ip nat inside destination and ip nat outside source . Networks to which these interfaces connect can then be thought of as inside networks or outside networks, respectively. Local address—A local address is any address that appears on the inside portion of the network. Global address—A global address is any address that appears on the outside portion of the network.
Q93. - (Topic 1)
To what type of port would a cable with a DB-60 connector attach?
A. Serial port
B. Console port
C. Ethernet port
D. Fibre optic port
Answer: A
Explanation:
Serial Connection
cl_3_dte_male
cl_2_dce
The picture on the left shows a V.35 DTE cable with a male DB60 connector and a male standard 34-pin Winchester-type connector. The right picture shows a V.35 DCE serial cable with a male DB60 connector and a female 34-pin Winchester-type connector. As you probably guessed already, the male connector of the DTE cable is attached to the DCE cable's female connector, this is depicted in the picture below. This is known as a back-to-back connection, and 'simulates' a WAN link. In a real world setup, the DTE cable's male connector typically connects to a port on a CSU/DSU provided by a service provider (i.e. telco), which in turn connects to a CSU/DSU at another location, thru a T1 link for example.
The DB60 connector connects to a Serial interface on a router.
cl_4_malefemale Reference: http://www.techexams.net/techlabs/ccna/lab_hardware.shtml
Q94. - (Topic 5)
Refer to the exhibit.
Why did the device return this message?
A. The command requires additional options or parameters
B. There is no show command that starts with ru.
C. The command is being executed from the wrong router mode.
D. There is more than one show command that starts with the letters ru.
Answer: D Explanation:
Answer D is correct because when you type the incomplete command it will not autocomplete if there is more than one option for completing the command. In this case, there is another command that also starts with “show ru”
Q95. - (Topic 3)
Refer to the exhibit.
The internetwork is using subnets of the address 192.168.1.0 with a subnet mask of
255.255.255.224. The routing protocol in use is RIP version 1. Which address could be assigned to the FastEthernet interface on RouterA?
A. 192.168.1.31
B. 192.168.1.64
C. 192.168.1.127
D. 192.168.1.190
E. 192.168.1.192
Answer: D
Explanation:
Subnet mask 255.255.255.224 with CIDR of /27 which results in 32 hosts per.
192.168.1.31 is the broadcast address for sunbet '0'
192.168.1.64 is the network address for subnet '2'
192.168.1.127 is the broadcast address for subnet '3'
192.168.1.192 is the network address for subnet '6'
Updated 100-105 test engine:
Q96. - (Topic 1)
Which network device functions only at Layer 1 of the OSI model? A. Option A
B. Option B
C. Option C
D. Option D
E. Option E
Answer: B
Explanation:
Most hubs are amplifying the electrical signal; therefore, they are really repeaters with several ports. Hubs and repeaters are Layer 1 (physical layer) devices.
Q97. - (Topic 7)
Which statement about native VLAN traffic is true?
A. Cisco Discovery Protocol traffic travels on the native VLAN by default
B. Traffic on the native VLAN is tagged with 1 by default
C. Control plane traffic is blocked on the native VLAN.
D. The native VLAN is typically disabled for security reasons
Answer: B
Q98. - (Topic 1)
Refer to the exhibit.
The output is from a router in a large enterprise. From the output, determine the role of the router.
A. A Core router.
B. The HQ Internet gateway router.
C. The WAN router at the central site.
D. Remote stub router at a remote site.
Answer: D
Explanation:
Since the routing table shows only a single default route using the single interface serial 0/0, we know that this is most likely a remote stub site with a single connection to the rest of the network. All the other answer options would mean that this router would have more connections, and would contain more routes.
Q99. - (Topic 7)
By default, how many MAC addresses are permitted to be learned on a switch port with port security enabled?
A. 8
B. 2
C. 1
D. 0
Answer: C
Q100. - (Topic 5)
Select two options which are security Issues which need to be modified before RouterA is used? (Choose two.)
A. unencrypted weak password is configured to protect privilege mode
B. inappropriate wording in banner message
C. the virtual terminal lines have a weak password configured
D. virtual terminal lines have a password, but it will not be used
E. configuration supports un-secure web server access
Answer: B,D