Master the 200 105 icnd2 ICND2 Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) content and be ready for exam day success quickly with this Pass4sure 105 200 dumps. We guarantee it!We make it a reality and give you real 200 105 icnd2 questions in our Cisco icnd2 200 105 braindumps.Latest 100% VALID Cisco 105 200 Exam Questions Dumps at below page. You can use our Cisco ccna routing and switching icnd2 200 105 official cert guide braindumps and pass your exam.
P.S. Tested 200-105 preparation labs are available on Google Drive, GET MORE: https://drive.google.com/open?id=1LPOwiv-vOUqlzBFPqF4sLauwGHst3olw
New Cisco 200-105 Exam Dumps Collection (Question 16 - Question 25)
Q1. Which IPsec security protocol should be used when confidentiality is required?
A. MD5
B. PSK
C. AH
D. ESP
Answer: D
Q2. In the Frame Relay network,
which IP addresses would be assigned to the interfaces with point-to-point PVCs?
A. DLCI 16 192.168.10.1/24
DLCI 17 192.168.10.1/24
DLCI 99 192.168.10.2/24
DLCI 28 192.168.10.3/24
B. DLCI 16 192.168.10.1 /24
DLCI 17 192.168.11.1/24
DLCI 99 192.168.12.1/24
DLCI 28 192.168.13.1/24
C. DLCI 16 192.168.10.1/24 DLCI 17 192.168.11.1/24
DLCI 99 192.168.10.2/24
DLCI 28 192.168.11.2/24
D. DLCI 16 192.168.10.1/24
DLCI 17 192.168.10.2/24
DLCI 99 192.168.10.3/24
DLCI 28 192.168.10.4/24
Answer: C
Explanation:
DLCI 16 and DLCI 19 need to act like a point-to-point link and will therefore need to be on the same network as will DLCI 17 and DLCI 28. With this information we can see that option "B" is the only option that has the corresponding DLCI's on the same network based on the ip addresses and subnetmask.
Option "D" is incorrect because, this would put the same network on both interfaces of the R2 router. Option "A" is similar.
Q3. Refer to the exhibit.
If the router R1 returns the given output and has not had its router ID set manually, what address will EIGRP use as its router ID?
A. 192.168.1.2
B. 172.16.4.1
C. 192.168.10.2
D. 1.1.1.1
Answer: D
Explanation:
The router ID is selected according to the following rules:
u2711 manual configuration
u2711 highest up/up loopback
u2711 highest up/up physical interface
Q4. Which process is associated with spanning-tree convergence?
A. determining the path cost
B. electing designated ports
C. learning the sender bridge ID
D. assigning the port ID
Answer: B
Explanation:
Spanning Tree Protocol (STP) convergence (Layer 2 convergence) happens when bridges and switches have transitioned to either the forwarding or blocking state. When layer 2 is converged, Root Switch is elected and Root Ports, Designated Ports and Non-Designated ports in all switches are selected. At Converged condition, the Root Ports and the Designated ports are in forwarding state, and all other ports are in blocking state.
Q5. Which statement about MPLS is true?
A. It operates in Layer 1.
B. It operates between Layer 2 and Layer 3.
C. It operates in Layer 3.
D. it operates in Layer 2.
Answer: B
Explanation: MPLS belongs to the family of packet-switched networks. MPLS operates at a layer that is generally considered to lie between traditional definitions of OSI Layer 2 (data link layer) and Layer 3 (network layer), and thus is often referred to as a layer 2.5 protocol.
Q6. Which protocol supports sharing the VLAN configuration between two or more switches?
A. multicast
B. STP
C. VTP
D. split-horizon
Answer: C
Explanation:
u201cVTP allows a network manager to configure a switch so that it will propagate VLAN configurations to other switches in the networku201d
VTP minimizes misconfigurations and configuration inconsistencies that can cause problems, such as duplicate VLAN names or incorrect VLAN-type specifications. VTP helps you simplify management of the VLAN database across multiple switches.
VTP is a Cisco-proprietary protocol and is available on most of the Cisco switches.
Q7. Refer to the exhibit.
While troubleshooting a switch, you executed the show interface port-channel 1 etherchannel command and it returned this output. Which information is provided by the Load value?
A. the percentage of use of the link
B. the preference of the link
C. the session count of the link
D. the number source-destination pairs on the link
Answer: D
Q8. Which configuration enables OSPF for network 192.168.1.0/24?
A. router ospf
router-id 192.168.1.0
B. router ospf 1
network 192.168.1.0 255.255.255.0 area 0
C. router ospf 1 neighbor 192.168.1.0
D. router ospf 1
area 0 virtual-link 192.168.1.0
Answer: B
Q9. Which two switch states are valid for 802.1w? (Choose two.)
A. listening
B. backup
C. disabled
D. learning
E. discarding
Answer: D,E
Explanation: Port States
There are only three port states left in RSTP that correspond to the three possible operational states. The 802.1D disabled, blocking, and listening states are merged into a unique 802.1w discarding state.
Q10. The command show frame-relay map gives the following output:
Serial 0 (up): ip 192.168.151.4 dlci 122, dynamic, broadcast, status defined, active Which statements represent what is shown?(Choose three.)
A. 192.168.151.4 represents the IP address of the remote router
B. 192.168.151.4 represents the IP address of the local serial interface
C. DLCI 122 represents the interface of the remote serial interface
D. DLCI 122 represents the local number used to connect to the remote address
E. broadcast indicates that a dynamic routing protocol such as RIP v1 can send packets across this PVC
F. active indicates that the ARP process is working
Answer: A,D,E
Explanation: http://www.cisco.com/en/US/docs/ios/12_2/wan/command/reference/wrffr4.html#wp102934 3
P.S. Easily pass 200-105 Exam with Allfreedumps Tested Dumps & pdf vce, Try Free: https://www.allfreedumps.com/200-105-dumps.html (267 New Questions)