Cause all that matters here is passing the Cisco 200 125 ccna pdf exam. Cause all that you need is a high score of ccna 200 120 vs 200 125 CCNA Cisco Certified Network Associate CCNA (v3.0) exam. The only one thing you need to do is downloading Exambible ccna 200 120 vs 200 125 exam study guides now. We will not let you down with our money-back guarantee.
Q136. - (Topic 8)
Which option is the default switch port port-security violation mode?
A. shutdown
B. protect
C. shutdown vlan
D. restrict
Answer: A
Explanation:
Shutdown—This mode is the default violation mode; when in this mode, the switch will automatically force the switchport into an error disabled (err-disable) state when a violation occurs. While in this state, the switchport forwards no traffic. The switchport can be brought out of this error disabled state by issuing the errdisable recovery cause CLI command or by disabling and reenabling the switchport.
Shutdown VLAN—This mode mimics the behavior of the shutdown mode but limits the error disabled state the specific violating VLAN.
Q137. - (Topic 7)
What command visualizes the general NetFlow data on the command line?
A. show ip flow export
B. show ip flow top-talkers
C. show ip cache flow
D. show mls sampling
E. show mls netflow ip
Answer: C
Explanation:
The following is an example of how to visualize the NetFlow data using the CLI. There are three methods to visualize the data depending on the version of Cisco IOS Software. The traditional show command for NetFlow is "show ip cache flow" also available are two forms of top talker commands. One of the top talkers commands uses a static configuration to view top talkers in the network and another command called dynamic top talkers allows real-time sorting and aggregation of NetFlow data. Also shown is a show MLS command to view the hardware cache on the Cisco Catalyst 6500 Series Switch.
The following is the original NetFlow show command used for many years in Cisco IOS Software. Information provided includes packet size distribution; basic statistics about number of flows and export timer setting, a view of the protocol distribution statistics and the NetFlow cache.
The “show ip cache flow” command displays a summary of the NetFlow accounting statistics.
Reference: http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/ios-netflow/prod_white_paper0900aecd80406232.html
Q138. - (Topic 5)
What are three benefits of GLBP? (Choose three.)
A. GLBP supports up to eight virtual forwarders per GLBP group.
B. GLBP supports clear text and MD5 password authentication between GLBP group members.
C. GLBP is an open source standardized protocol that can be used with multiple vendors.
D. GLBP supports up to 1024 virtual routers.
E. GLBP can load share traffic across a maximum of four routers.
F. GLBP elects two AVGs and two standby AVGs for redundancy.
Answer: B,D,E
Q139. - (Topic 3)
Refer to the exhibit.
The Lakeside Company has the internetwork in the exhibit. The administrator would like to
reduce the size of the routing table on the Central router. Which partial routing table entry in the Central router represents a route summary that represents the LANs in Phoenix but no additional subnets?
A. 10.0.0.0/22 is subnetted, 1 subnets
D 10.0.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
B. 10.0.0.0/28 is subnetted, 1 subnets
D 10.2.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
C. 10.0.0.0/30 is subnetted, 1 subnets
D 10.2.2.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
D. 10.0.0.0/22 is subnetted, 1 subnets
D 10.4.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
E. 10.0.0.0/28 is subnetted, 1 subnets
D 10.4.4.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
F. 10.0.0.0/30 is subnetted, 1 subnets
D 10.4.4.4 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
Answer: D
Explanation:
The 10.4.0.0/22 route includes 10.4.0.0/24, 10.4.1.0/24, 10.4.2.0/24 and 10.4.3.0/24 networks only.
Q140. - (Topic 3)
Refer to the exhibit.
The two exhibited devices are the only Cisco devices on the network. The serial network between the two devices has a mask of 255.255.255.252. Given the output that is shown, what three statements are true of these devices? (Choose three.)
A. The Manchester serial address is 10.1.1.1.
B. The Manchester serial address is 10.1.1.2.
C. The London router is a Cisco 2610.
D. The Manchester router is a Cisco 2610.
E. The CDP information was received on port Serial0/0 of the Manchester router.
F. The CDP information was sent by port Serial0/0 of the London router.
Answer: A,C,E
Explanation:
From the output, we learn that the IP address of the neighbor router is 10.1.1.2 and the question stated that the subnet mask of the network between two routers is 255.255.255.252. Therefore there are only 2 available hosts in this network (22 – 2 = 2). So we can deduce the ip address (of the serial interface) of Manchester router is 10.1.1.1 ->. The platform of the neighbor router is cisco 2610, as shown in the output ->.
Maybe the most difficult choice of this question is the answer E or F. Please notice that “Interface” refers to the local port on the local router, in this case it is the port of Manchester router, and “Port ID (outgoing port)” refers to the port on the neighbor router.
Q141. - (Topic 8)
Which two statements about the tunnel mode ipv6ip command are true? (Choose two.)
A. It enables the transmission of IPv6 packets within the configured tunnel.
B. It specifies IPv4 as the encapsulation protocol.
C. It specifies IPv6 as the encapsulation protocol.
D. It specifies IPv6 as the transport protocol.
E. It specifies that the tunnel is a Teredo tunnel.
Answer: A,B
Q142. - (Topic 4)
What command is used to verify the DLCI destination address in a Frame Relay static configuration?
A. show frame-relay pvc
B. show frame-relay lmi
C. show frame-relay map
D. show frame relay end-to-end
Answer: C
Explanation:
Sample “show frame-relay map” output: R1#sh frame map
Serial0/0 (up): ip 10.4.4.1 dlci 401(0x191,0x6410), dynamic, broadcast,, status defined, active
Serial0/0 (up): ip 10.4.4.3 dlci 403(0x193,0x6430), dynamic, broadcast,, status defined, active
Serial0/0 (up): ip 10.4.4.4 dlci 401(0x191,0x6410), static, CISCO, status defined, active
Q143. - (Topic 5)
Refer to the exhibit.
In this VLSM addressing scheme, what summary address would be sent from router A?
A. 172.16.0.0 /16
B. 172.16.0.0 /20
C. 172.16.0.0 /24
D. 172.32.0.0 /16
E. 172.32.0.0 /17
F. 172.64.0.0 /16
Answer: A
Explanation:
Router A receives 3 subnets: 172.16.64.0/18, 172.16.32.0/24 and 172.16.128.0/18.
All these 3 subnets have the same form of 172.16.x.x so our summarized subnet must be also in that form -> Only A, B or .
The smallest subnet mask of these 3 subnets is /18 so our summarized subnet must also have its subnet mask equal or smaller than /18.
-> Only answer A has these 2 conditions ->.
Q144. - (Topic 4)
It has become necessary to configure an existing serial interface to accept a second Frame Relay virtual circuit. Which of the following procedures are required to accomplish this task? (Choose three.)
A. Remove the IP address from the physical interface.
B. Encapsulate the physical interface with multipoint PPP.
C. Create the virtual interfaces with the interface command.
D. Configure each subinterface with its own IP address.
E. Disable split horizon to prevent routing loops between the subinterface networks.
F. Configure static Frame Relay map entries for each subinterface network.
Answer: A,C,D
Explanation:
For multiple PVC’s on a single interface, you must use subinterfaces, with each subinterface configured for each PVC. Each subinterface will then have its own IP address, and no IP address will be assigned to the main interface.
Q145. - (Topic 5)
Which statement describes VRRP object tracking?
A. It monitors traffic flow and link utilization.
B. It ensures the best VRRP router is the virtual router master for the group.
C. It causes traffic to dynamically move to higher bandwidth links.
D. It thwarts man-in-the-middle attacks.
Answer: B
Explanation:
Object tracking is the process of tracking the state of a configured object and uses that state to determine the priority of the VRRP router in a VRRP group.
Q146. - (Topic 4)
Which encapsulation type is a Frame Relay encapsulation type that is supported by Cisco routers?
A. IETF
B. ANSI Annex D
C. Q9333-A Annex A
D. HDLC
Answer: A
Explanation:
Cisco supports two Frame Relay encapsulation types: the Cisco encapsulation and the IETF Frame Relay encapsulation, which is in conformance with RFC 1490 and RFC 2427. The former is often used to connect two Cisco routers while the latter is used to connect a Cisco router to a non-Cisco router. You can test with your Cisco router when typing the command Router(config-if)#encapsulation frame-relay ? on a WAN link. Below is the output of this command (notice Cisco is the default encapsulation so it is not listed here, just press Enter to use it).
Note: Three LMI options are supported by Cisco routers are ansi, Cisco, and Q933a. They
represent the ANSI Annex D, Cisco, and ITU Q933-A (Annex A) LMI types, respectively. HDLC is a WAN protocol same as Frame-Relay and PPP so it is not a Frame Relay encapsulation type.
Q147. - (Topic 5)
Refer to the exhibit.
What is the cause of the Syslog output messages?
A. The EIGRP neighbor on Fa0/1 went down due to a failed link.
B. The EIGRP neighbor connected to Fa0/1 is participating in a different EIGRP process, causing the adjacency to go down.
C. A shut command was executed on interface Fa0/1, causing the EIGRP adjacency to go down.
D. Interface Fa0/1 has become error disabled, causing the EIGRP adjacency to go down.
Answer: C
Explanation:
The first lines of the message show that a configuration change was made, and that the fa0/1 interface changed to a state of administratively down. This can only be done by issuing the shutdown command. The last line indicates that this caused an EIGRP neighbor adjacency to go down.
Q148. - (Topic 8)
Which route source code represents the routing protocol with a default administrative distance of 90 in the routing table?
A. S
B. E
C. D
D. R
E. O
Answer: C
Explanation:
SStatic EEGP DEIGRP RRIP OOSPF
Default Administrative distance of EIGRP protocol is 90 then answer is C
Default Distance Value TableThis table lists the administrative distance default values of the protocols that Cisco supports:
Route Source
Default Distance Values
Connected interface 0
Static route 1
Enhanced Interior Gateway Routing Protocol (EIGRP) summary route 5
External Border Gateway Protocol (BGP) 20
Internal EIGRP 90
IGRP 100 OSPF 110
Intermediate System-to-Intermediate System (IS-IS) 115
Routing Information Protocol (RIP) 120
Exterior Gateway Protocol (EGP) 140
On Demand Routing (ODR) 160
External EIGRP 170
Internal BGP 200
Unknown* 255
Q149. - (Topic 5)
What is a valid HSRP virtual MAC address?
A. 0000.5E00.01A3
B. 0007.B400.AE01
C. 0000.0C07.AC15
D. 0007.5E00.B301
Answer: C
Explanation:
With HSRP, two or more devices support a virtual router with a fictitious MAC address and unique IP address. There are two version of HSRP.
+ With HSRP version 1, the virtual router’s MAC address is 0000.0c07.ACxx , in which xx is the HSRP group.
+ With HSRP version 2, the virtual MAC address if 0000.0C9F.Fxxx, in which xxx is the HSRP group.
Note: Another case is HSRP for IPv6, in which the MAC address range from 0005.73A0.0000 through 0005.73A0.0FFF.
Q150. - (Topic 8)
Which condition does the err-disabled status indicate on an Ethernet interface?
A. There is a duplex mismatch.
B. The device at the other end of the connection is powered off.
C. The serial interface is disabled.
D. The interface is configured with the shutdown command.
E. Port security has disabled the interface.
F. The interface is fully functioning.
Answer: E