Exam Code: 300 075 ciptv2 (Practice Exam Latest Test Questions VCE PDF)
Exam Name: Implementing Cisco IP Telephony and Video, Part 2 (CIPTV2)
Certification Provider: Cisco
Free Today! Guaranteed Training- Pass 300 075 pdf Exam.
Q136. Scenario
There are two call control systems in this item. The Cisco UCM is controlling the Cisco Jabber for Windows Client, and the 7965 and 9971 Video IP Phone. The Cisco VCS is controlling the SX20, the Cisco TelePresence MCU, and the Cisco Jabber TelePresence for Windows.
Use the exhibits to answer the following questions.
DP
Locations
CSS
Movi Failure
Movi Settings
CIPTV Topo
Subzone
Links
Pipe
A third collaboration call fails between the backbone site and the HQ site. After reviewing the exhibits, which of the following reasons could be causing this failure?
A. Not enough bandwidth has been allocated.
B. Device Pool.
C. Location.
D. The pipe is not functioning.
Answer: A
Explanation:
Based on the exhibit, each call is limited to no more than 128kbps per call, but the total available bandwidth is set to 256 kbps. This will allow the first to calls to go through, but there will be no more available bandwidth for the third call.
Q137. Which action configures phones in site A to use G.711 to site B but to use G.729 to site C?
A. Configure Cisco Unified Communications Manager regions.
B. Configure Cisco Unified Communications Manager locations.
C. Configure transcoder resources in Cisco Unified Communications Manager.
D. Configure a gatekeeper.
Answer: A
Q138. Refer to the following exhibits.
Users in the U.S dial Germany by calling 9011 49 followed by the remaining digits. What would be the most suitable configuration for Connection X?
A. Configure a SIP trunk to 10.140.1.1 and a SIP route pattern +49T in Cisco Unified Communications Manager.
B. Configure a SIP trunk to the Cisco Unified Border Element and route pattern +49T in Cisco Unified Communications Manager.
C. configure a SIP trunk to the Cisco Unified Border Element. Configure a translation pattern for 9011.49T using DDI Predot prefix + and CSS to point to a route pattern partition \+! which uses the SIP trunk.
D. Configure a SIP trunk to the ITSP. Configure a translation pattern for 9011.49T using DDI predot prefix + and CSS to point to a route pattern partition \+! which uses the SIP trunk.
Answer: C
Explanation:
Incorrect Answer: A, B, D SIP trunks for public switched telephone network (PSTN) access are an important new access method for business collaboration. Service providers throughout the world offer SIP trunking as an alternative to traditional TDM (T1/E1) connections. A discard digits instruction (DDI) removes a portion of the dialed digit string before passing the number on to the adjacent system. A DDI must remove portions of the digit string, for example, when an external access code is needed to route the call to the PSTN, but the PSTN switch does not expect that access code.
Link: https://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/8_6_1/ccmsys/a03rp.html
Q139. Which three commands are necessary to override the default CoS to DSCP mapping on interface Fastethernet0/1? (Choose three.)
A. mls qos map cos-dscp 0 10 18 26 34 46 48 56
B. mls qos map dscp-cos 8 10 to 2
C. mls qos
D. interface Fastethernet0/1mls qos trust cos
E. interface Fastethernet0/1mls qos cos 1
F. interface Fastethernet0/2mls qos cos 1
Answer: A,C,D
Q140. In a cluster-wide deployment, what is the maximum number of Service Advertisement Framework forwarders to which the Cisco Unified Communications Manager can connect?
A. 1
B. 2
C. 3
D. 4
E. 6
F. as many as are configured
Answer: B
Q141. Refer to the exhibit.
Assume that NANP is being used and 9 is used for PSTN access code Long distance national calls are preceded with 1.
How should the HQ Cisco Unified Communications Manager be configured for calls to 3XXX to be sent to the gatekeeper at 1 0 1 6 1 with PSTN backups?
A. Configure a route pattern for 3XXX Assign this route pattern to a route list that points to two route groups The first route group contains the H 225 trunk The second route group contains the MGCP gateway with prefix digits 1 408555 for the outgoing called number.
B. Configure a route pattern for 1#3XXX Assign this route pattern to a route list that points to a route group that lists the H 225 trunk as first choice and the MGCP gateway as a second choice.
C. Configure a route pattern for 4085543XXX. Assign this route pattern to a route list that points to two route groups. The first route group contains the H 226 trunk The second route group contains MGCP gateway.
D. Configure a route pattern for 3XXX Assign this route pattern to a route list that points to two route groups The first route group contains the H 225 trunk The second route group contains MGCP gateway with prefix digits 91 408554 for the called number.
Answer: A
Explanation:
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/8_6_1/ccmcfg/b03rtgrp.html #wpxref46617
Q142. The relationship between a Region and a Location is that the Region codec parameter is used between a Region and its configured Locations.
A. TRUE
B. FALSE
Answer: B
Explanation:
Locations work in conjunction with regions to define the characteristics of a network link. Regions define the type of compression (G.711, G.722, G.723, G.729, GSM, or wideband) that is used on the link, and locations define the amount of available bandwidth for the link Link:
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/8_6_1/ccmsys/a02cac.html #wp1033331
Q143. Which CAC configuration on a gatekeeper restricts to 10 G.711 audio calls?
A. Use the command bandwidth 10.
B. Use the command bandwidth 1280.
C. Use the command bandwidth 160.
D. Use the command bandwidth session 10.
Answer: B