we provide Validated Cisco ccnp routing and switching route 300 101 official cert guide free practice exam which are the best for clearing 300 101 route pdf test, and to get certified by Cisco ROUTE Implementing Cisco IP Routing. The 300 101 pdf Questions & Answers covers all the knowledge points of the real ccnp route 300 101 pdf exam. Crack your Cisco ccnp routing and switching route 300 101 Exam with latest dumps, guaranteed!
P.S. Validated 300-101 forum are available on Google Drive, GET MORE: https://drive.google.com/open?id=1oF6hAYEiseB3LPIXYA2sgTXv0r2MX46d
New Cisco 300-101 Exam Dumps Collection (Question 14 - Question 23)
New Questions 14
If the total bandwidth is 64 kbps and the RTT is 3 seconds, what is the bandwidth delay product?
A. 8,000 bytes
B. 16,000 bytes
C. 24,000 bytes
D. 32,000 bytes
E. 62,000 bytes
Answer: C
New Questions 15
Which three functionalities are specific to stateful NAT64? (Choose Three)
A. It requires IPv4-transalable IPv6 address
B. It requires either manual or DHCPv6 based address assignment for IPv6 host.
C. It helps ensure end-to-end address transparency and scalability.
D. A state or bindings are created on every unique translation.
E. It conserves IPv4 addresses.
Answer: B,D,E
New Questions 16
Refer to the exhibit.
Which command would verify if PBR reacts to packets sourced from 172.16.0.0/16?
A. show ip route
B. show policy-map
C. show access-lists
D. show route-map
Answer: D
Explanation:
The u201cshow route-map u201croute-map nameu201d displays the policy routing match counts so we can learn if PBR reacts to packets sourced from 172.16.0.0/16 or not.
New Questions 17
What is the purpose of the route-target command?
A. It extends the IP address to identify which VRF instance it belongs to.
B. It enables multicast distribution for VRF-Lite setups to enhance IGP routing protocol capabilities.
C. It manages the import and export of routes between two or more VRF instances.
D. It enables multicast distribution for VRF-Lite setups to enhance EGP routing protocol capabilities.
Answer: C
New Questions 18
What does the show ip route vrf CISCO command display?
A. directly connected routes for VRF CISCO.
B. the routing table for VRF CISCO.
C. the global routing table.
D. all routing tables that start with VRF CISCO.
E. the route distinguisher for VRF CISCO
Answer: B
New Questions 19
ALWAYS block the outbound web traffic on Saturdays and Sunday between 1:00 to 23:59
A. periodic Saturday Sunday 01:00 to 23:59 and IN
B. periodic Saturday Sunday 01:00 to 23:59 and OUT
C. periodic Saturday Sunday 01:00 to 11:59 and IN
D. Absolute Saturday Sunday 01:00 to 11:59 and IN
Answer: B
New Questions 20
Refer to the exhibit. Which option describes why the EIGRP neighbors of this router are not learning routes that are received fromOSPF?
A. The subnet defined in OSPF is not part of area 0.
B. Default metrics are not configured under EIGRP.
C. There is no overlap in the subnets advertised.
D. The routing protocols do not have the same AS number.
Answer: B
New Questions 21
Which two functionalities are specific to stateless NAT64? (Choose two.)
A. No requirement exists for the characteristics of Ipv6 address assignment.
B. It does not conserve Ipv4 addresses.
C. It provides 1-to-1 translation.
D. It uses address overloading.
E. State or bindings are created on the translation.
Answer: B,C
New Questions 22
Refer to the exhibit.
How would you confirm on R1 that load balancing is actually occurring on the default- network (0.0.0.0)?
A. Use ping and the show ip route command to confirm the timers for each default network resets to 0.
B. Load balancing does not occur over default networks; the second route will only be used for failover.
C. Use an extended ping along with repeated show ip route commands to confirm the gateway of last resort address toggles back and forth.
D. Use the traceroute command to an address that is not explicitly in the routing table.
Answer: D
Explanation:
The most simple method to test load balancing is to use the u201ctracerouteu201d command. If load balancing is working correctly, we will see different paths to reach the destination each time
we use that command.
Unknown address will be routed via the default-network 0.0.0.0 so we must use an address that is not explicitly in the routing table.
New Questions 23
After testing various dynamic IPv6 address assignment methods, an engineer decides that more control is needed when distributing addresses to clients. Which two advantages does DHCPv6 have over EUI-64 (Choose two.)
A. DHCPv6 requires less planning and configuration than EUI-64 requires.
B. DHCPv6 allows for additional parameters to be sent to the client, such as the domain name and DNS server.
C. DHCPv6 providers tighter control over the IPv6 addresses that are distributed to clients.
D. DHCPv6 does not require the configuration of prefix pools.
E. DHCPv6 does not require neighbor and router discovery on the network segment.
Answer: A,B
Recommend!! Get the Validated 300-101 dumps in VCE and PDF From Thedumpscentre, Welcome to download: http://www.thedumpscentre.com/300-101-dumps/ (New 436 Q&As Version)