Precise of 300 115 switch free draindumps materials and lab for Cisco certification for consumer, Real Success Guaranteed with Updated 9tut ccnp switch 300 115 pdf dumps vce Materials. 100% PASS Implementing Cisco IP Switched Networks exam Today!
Q31. Which command would a network engineer apply to error-disable a switchport when a packet-storm is detected?
A. router(config-if)#storm-control action shutdown
B. router(config-if)#storm-control action trap
C. router(config-if)#storm-control action error
D. router(config-if)#storm-control action enable
Answer: A
Q32. Which configuration command ties the router hot standby priority to the availability of its interfaces?
A. standby group
B. standby priority
C. backup interface
D. standby track
Answer: D
Q33. A network engineer configured a fault-tolerance link on Gigabit Ethernet links G0/1, G0/2, G0/3, and G0/4 between two switches using Ethernet port-channel. Which action allows interface G0/1 to always actively forward traffic in the port-channel?
A. Configure G0/1 as half duplex and G0/2 as full duplex.
B. Configure LACP port-priority on G0/1 to 1.
C. Configure LACP port-priority on G0/1 to 65535.
D. LACP traffic goes through G0/4 because it is the highest interface ID.
Answer: B
Q34. Which AAA Authorization type includes PPP, SLIP, and ARAP connections?
A. network
B. IP mobile
C. EXEC
D. auth-proxy
Answer: A
Q35. Several new switches have been added to the existing network as VTP clients. All of the new switches have been configured with the same VTP domain, password, and version. However, VLANs are not passing from the VTP server (existing network) to the VTP clients. What must be done to fix this?
A. Remove the VTP domain name from all switches with "null" and then replace it with the new domain name.
B. Configure a different native VLAN on all new switches that are configured as VTP clients.
C. Provision one of the new switches to be the VTP server and duplicate information from the existing network.
D. Ensure that all switch interconnects are configured as trunks to allow VTP information to be transferred.
Answer: D
Q36. Which four LACP components are used to determine which hot-standby links become active after an interface failure within an EtherChannel bundle? (Choose four.)
A. LACP system priority
B. LACP port priority
C. interface MAC address
D. system ID
E. port number
F. hot-standby link identification number
G. interface bandwidth
Answer: ABDE
Q37. Refer to the exhibit.
A multilayer switch has been configured to send and receive encapsulated and tagged frames. VLAN 2013 on the multilayer switch is configured as the native VLAN. Which option is the cause of the spanning-tree error?
A. VLAN spanning-tree in SW-2 is configured.
B. spanning-tree bpdu-filter is enabled.
C. 802.1q trunks are on both sides, both with native VLAN mismatch.
D. VLAN ID 1 should not be used for management traffic because its unsafe.
Answer: C
Q38. What is the maximum number of 10 Gigabit Ethernet connections that can be utilized in an EtherChannel for the virtual switch link?
A. 4
B. 6
C. 8
D. 12
Answer: C
Q39. A DHCP configured router is connected directly to a switch that has been provisioned with DHCP snooping. IP Source Guard with the ip verify source port-security command is configured under the interfaces that connect to all DHCP clients on the switch. However, clients are not receiving an IP address via the DHCP server. Which option is the cause of this issue?
A. The DHCP server does not support information option 82.
B. The DHCP client interfaces have storm control configured.
C. Static DHCP bindings are not configured on the switch.
D. DHCP snooping must be enabled on all VLANs, even if they are not utilized for dynamic address allocation.
Answer: A
Q40. Which statement about using native VLANs to carry untagged frames is true?
A. Cisco Discovery Protocol version 2 carries native VLAN information, but version 1 does not.
B. Cisco Discovery Protocol version 1 carries native VLAN information, but version 2 does not.
C. Cisco Discovery Protocol version 1 and version 2 carry native VLAN information.
D. Cisco Discovery Protocol version 3 carries native VLAN information, but versions 1 and 2 do not.
Answer: A