Downloadable of cbt nuggets ccnp switch 300 115 download test preparation materials and keys for Cisco certification for IT candidates, Real Success Guaranteed with Updated 300 115 switch pdf dumps vce Materials. 100% PASS Implementing Cisco IP Switched Networks exam Today!
Q35. What is the default amount by which the hot standby priority for the router is decremented or incremented when the interface goes down or comes back up?
A. 1
B. 5
C. 10
D. 15
Answer: C
Q36. Which private VLAN access port belongs to the primary VLAN and can communicate with all interfaces, including the community and isolated host ports?
A. promiscuous port
B. isolated port
C. community port
D. trunk port
Answer: A
Q37. Which option lists the modes that are available for configuring UDLD on a Cisco switch?
A. normal and aggressive
B. active and aggressive
C. normal and active
D. normal and passive
E. normal and standby
Answer: A
Q38. A switch is added into the production network to increase port capacity. A network engineer is configuring the switch for DHCP snooping and IP Source Guard, but is unable to configure ip verify source under several of the interfaces. Which option is the cause of the problem?
A. The local DHCP server is disabled prior to enabling IP Source Guard.
B. The interfaces are configured as Layer 3 using the no switchport command.
C. No VLANs exist on the switch and/or the switch is configured in VTP transparent mode.
D. The switch is configured for sdm prefer routing as the switched database management template.
E. The configured SVIs on the switch have been removed for the associated interfaces.
Answer: B
Q39. What is the default value for the errdisable recovery interval in a Cisco switch?
A. 30 seconds
B. 100 seconds
C. 300 seconds
D. 600 seconds
Answer: C
Q40. What is the maximum number of virtual MAC addresses that GLBP allows per group?
A. 2
B. 4
C. 6
D. 8
Answer: B
Q41. Which statement describes what happens when a switch enters dual active recovery mode?
A. The switch shuts down and waits for the VSL link to be restored before sending traffic.
B. All interfaces are shut down in the formerly active virtual switch member, but the new active virtual switch forwards traffic on all links.
C. The switch continues to forward traffic out all links and enables spanning tree on VSL link and all other links to prevent loops.
D. The VSS detects which system was last in active state and shuts down the other switch.
Answer: B
Q42. Which statement about using EtherChannel on Cisco IOS switches is true?
A. A switch can support up to eight compatibly configured Ethernet interfaces in an EtherChannel. The EtherChannel provides full-duplex bandwidth up to 800 Mbps only for Fast EtherChannel or 8 Gbps only for Gigabit EtherChannel.
B. A switch can support up to 10 compatibly configured Ethernet interfaces in an EtherChannel. The EtherChannel provides full-duplex bandwidth up to 1000 Mbps only for Fast EtherChannel or 8 Gbps only for Gigabit EtherChannel.
C. A switch can support up to eight compatibly configured Ethernet interfaces in an EtherChannel. The EtherChannel provides full-duplex bandwidth up to 800 Mbps only for Fast EtherChannel or 16 Gbps only for Gigabit EtherChannel.
D. A switch can support up to 10 compatibly configured Ethernet interfaces in an EtherChannel. The EtherChannel provides full-duplex bandwidth up to 1000 Mbps only for Fast EtherChannel or 10 Gbps only for Gigabit EtherChannel.
Answer: A
Q43. Which technique automatically limits VLAN traffic to only the switches that require it?
A. access lists
B. DTP in nonegotiate
C. VTP pruning
D. PBR
Answer: C
Q44. Which portion of AAA looks at what a user has access to?
A. authorization
B. authentication
C. accounting
D. auditing
Answer: A
Q45. A network is running VTPv2. After verifying all VTP settings, the network engineer notices that the new switch is not receiving the list of VLANs from the server. Which action resolves this problem?
A. Reload the new switch.
B. Restart the VTP process on the new switch.
C. Reload the VTP server.
D. Verify connected trunk ports.
Answer: D
Q46. which feature is automatically enabled when a voice VLAN is configured, but not automatically disabled when a voice VLAN is removed?
A. portfast
B. port-security
C. spanning tree
D. storm control
Answer: A
Q47. what percentage of bandwidth is reduced when a stack cable is broken?
A. 0
B. 25
C. 50
D. 75
E. 100
Answer: C
Q48. The network manager has requested that several new VLANs (VLAN 10, 20, and 30) are allowed to traverse the switch trunk interface. After the command switchport trunk allowed vlan 10,20,30 is issued, all other existing VLANs no longer pass traffic over the trunk. What is the root cause of the problem?
A. The command effectively removed all other working VLANs and replaced them with the new VLANs.
B. VTP pruning removed all unused VLANs.
C. ISL was unable to encapsulate more than the already permitted VLANs across the trunk.
D. Allowing additional VLANs across the trunk introduced a loop in the network.
Answer: A
Q49. What is the maximum number of 10 Gigabit Ethernet connections that can be utilized in an EtherChannel for the virtual switch link?
A. 4
B. 6
C. 8
D. 12
Answer: C
Q50. RSPAN has been configured on a Cisco Catalyst switch; however, traffic is not being replicated to the remote switch. Which type of misconfiguration is a cause?
A. The RSPAN designated VLAN is missing the remote span command.
B. The local and remote RSPAN switches are configured using different session IDs.
C. The local RSPAN switch is replicating only Rx traffic to the remote switch.
D. The local switch is overloaded with the amount of sourced traffic that must be replicated to the remote switch.
Answer: A
Q51. Refer to the exhibit.
How can the traffic that is mirrored out the GigabitEthernet0/48 port be limited to only traffic that is received or transmitted in VLAN 10 on the GigabitEthernet0/1 port?
A. Change the configuration for GigabitEthernet0/48 so that it is a member of VLAN 10.
B. Add an access list to GigabitEthernet0/48 to filter out traffic that is not in VLAN 10.
C. Apply the monitor session filter globally to allow only traffic from VLAN 10.
D. Change the monitor session source to VLAN 10 instead of the physical interface.
Answer: C