Virtual of 300-360 torrent materials and interactive bootcamp for Cisco certification for customers, Real Success Guaranteed with Updated 300-360 pdf dumps vce Materials. 100% PASS Designing Cisco Wireless Enterprise Networks exam Today!
Q11. A downstream packet that contains a DSCP value arrives at the WLC Ethernet interface from the wired source network. The WLC is configured for QoS WLAN 802.1p mapping. How does the WLC treat the CAPWAP QoS marking when leaving the controller interface for the respective AP and final wireless client destination?
A. No outer CAPWAP or inner QoS tagging is applied.
B. The outer CAPWAP CoS is marked and capped and the inner DSCP maintains the original marking.
C. No outer CAPWAP QoS tag is applied, but the original DSCP is maintained inside CAPWAP.
D. The outer CAPWAP DHCP is marked and capped without any inner DSCP value.
Answer: B
Q12. An engineer is preparing for an active site survey of a warehouse and is informed that they should not enter any areas that are blocked by supplies that are difficult to move. Which option describes how the engineer should address this restriction?
A. Extrapolate restricted access areas by drawing circles for AP coverage
B. Survey hallways, common areas, and storerooms.
C. Utilize a predictive tool to define coverage in off-limits areas.
D. Educate the customer about the importance of accurate and complete measurements.
Answer: D
Q13. An engineer is performing a predictive wireless design for a Parts Distribution Center, which requires data and location services. Which three requirements are inputs to the design? (Choose three.)
A. access points with directional antennas
B. continuous -67 dBm coverage from one access point
C. overlapping -75 dBm coverage from three access points
D. overlapping -67 dBm coverage from two access points
E. access points in IPS mode
F. continuous -72 dBm coverage from one access point
G. access points in corners and along perimeters
Answer: B,C,G
Explanation: Reference: http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Mobility/WiFiLBS- DG/wifich5.html
Q14. The AP has been configured property for a VoWLAN survey The RF environment contains a noise of -87 to -90 dBm. What is the target value for the cell edge reading?
A. -62 dBm
B. -67 dBm
C. -60 dBm
D. -70 dBm
Answer: B
Q15. You have a customer that is building a new campus of four 3-story buildings that you have just completed the site survey for. The customer is interested in the mount of rack space they will need to allocate in either the building MDF or in the data center for controllers. Each building is going to require 75 APs to support voice and data. How should the controllers be deployed to provide the least number of controllers, the highest redundancy, and the easiest management?
A. Use the centralized deployment method in the data center with the N + N redundancy method.
B. Use the centralized deployment method in the data center with the N + 1 redundancy method
C. Use the centralized deployment method in the data center with the 1 + 1 redundancy method and clientSSO.
D. Use the distributed deployment method in each building MDF with the N + 1 redundancy method.
E. Use the distributed deployment method in each building MDF with the N + N + 1 redundancy method.
F. Use the distributed deployment method in each building MDF with the N + N redundancy method.
Answer: C
Q16. A customer has a business-critical voice network and wants to be alerted whenever voice clients move out of a coverage area and experience RSSI below -67 dBm on the 5 GHz band. Which option can be configured on the wireless controller to alert network administrators when this limit is surpassed?
A. EDCA; voice optimized
B. SIP voice sample interval
C. 802.11a voice RSSI coverage threshold
D. traffic stream metrics
Answer: C
Q17. An engineer is performing a predictive wireless design for a carpeted office space, which requires voice capability and location services. Which two requirements are inputs to the design? (Choose two.)
A. overlapping -67 dBm coverage from three access points
B. overlapping -75 dBm coverage from three access points
C. overlapping-72 dBm coverage from two access points
D. continuous -67 dBm coverage from one access point
E. continuous -72 dBm coverage from one access point
Answer: B,D
Explanation:
http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Mobility/emob73dg/emob73/ch3_WLAN.html#pgfId-1000250
Q18. A network engineer wants the DSCP marking to align with the 802.11e access category video. What will this marking be?
A. 34
B. AF31
C. 4
D. 5
Answer: A
Q19. A customer has restricted the AP and antenna combinations for a design to be limited to one model integrated antenna AP for carpeted spaces and one model external antenna AP, with high gain antennas for industrial, maintenance, or storage areas. When moving between a carpeted area to an industrial area, the engineer forgets to change survey devices and surveys several APs. Which option is the best to reduce the negative impact of the design?
A. Deploy the specified access points per area type.
B. Resurvey and adjust the design.
C. Increase the Tx power on incorrectly surveyed access points.
D. Deploy unsurveyed access points to the design.
Answer: B
Q20. While performing a Layer 1 passive wireless site survey of a location an engineer detects several instances of low power frequency hopping interference, but cannot physically locate the interfering device or devices. Why is the engineer unable to locate the offending device or devices?
A. The sources are nearby narrow-beam radar and are sweeping through the facility.
B. The sources are PAN and are mobile.
C. The sources are above the ceiling file and transmit intermittently.
D. The sources are actually high-powered devices and transmit from off the site.
Answer: B