Master the 300-360 Designing Cisco Wireless Enterprise Networks content and be ready for exam day success quickly with this Testking 300-360 test preparation. We guarantee it!We make it a reality and give you real 300-360 questions in our Cisco 300-360 braindumps.Latest 100% VALID Cisco 300-360 Exam Questions Dumps at below page. You can use our Cisco 300-360 braindumps and pass your exam.
Q31. An engineer is deploying centralized wireless solution with a 5508 controller. What is the most AP licenses that can be supported?
A. 100
B. 250
C. 1000
D. 500
Answer: D
Explanation:
You can order Cisco 5500 Series Controllers with support for 12, 25, 50, 100, 250 or 500 APs as the controller's base capacity. You can add additional AP capacity through capacity adder licenses available at 25, 50, 100 and 250 AP capacities. You can add the capacity adder licenses to any base license in any combination to arrive at the maximum capacity of 500 APs.
Reference: http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/112926-5508wlc-license.html
Q32. An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services. Which of the following is a requirement for the design?
A. overlapping -72 dBm coverage from two access points
B. overlapping -67 dBm coverage from two access points
C. continuous -67 dBm coverage from one access point
D. continuous -72 dBm coverage from one access point
Answer: C
Q33. An engineer is configuring an autonomous AP for RADIUS authentication. What three pieces of information must be known to configure the AP? (Choose three.)
A. BVI IP address
B. group name
C. RADIUS IP address
D. PAC encryption key
E. username and password
F. shared secret
Answer: A,C,F
Q34. Which two types of information must be included in the installation inventory portion of the post-installation report? (Choose two.)
A. all AP, controller, and MSE administrator credentials
B. the names, locations, IP addresses, MAC addresses, etc. for every AP, controller, and MSE in the WLAN
C. a layout of the rack that the equipment is installed
D. results of the coverage audit performed with the site survey mapping tool
E. the number and type of all WLAN clients and tags
Answer: A,B
Q35. An engineer is assigned to provide wireless coverage in a provincial capital building. Due to the age and historic nature of the building, the ability to run new copper Ethernet cable to desired AP locations is limited. Which requirement should the engineer specify to overcome this restriction?
A. Deploy access points where the survey indicates and connect them via fiber optic cable, using a mediaadapter, and locally provide power.
B. Deploy access points to each phone location converting two spare pairs of copper from the phone line toEthernet and locally provide power.
C. Deploy access point devices where limited cable can be run or exists and connect high- gain antennas andincrease Tx power to increase cell size.
D. Deploy RAP where limited cable can be run or exists, and extend coverage using MAP.
Answer: D
Q36. An engineer plugs in a Cisco Aironet 2700 Series Access Point and it is running in low power. Which three power requirements should be verified? (Choose three.)
A. 802.3ac compliant
B. 802.3at compliant
C. AP requires 43 VDC to function in full power.
D. AIR-PWRINJ3 power injector should be used.
E. AP requires 57 VDC to function in full power.
F. AIR-PWRINJ4 power injector should be used.
Answer: B,E,F
Explanation:
The access point should be powered by any 802.3at compliant device.
The recommended external power supply for the access point is the Cisco AIR-PWR-B power supply. The access point can also be powered by the following optional external power sources:
– Access point power injector (AIR-PWRINJ4)
– Any 802.3af compliant power injector is supported, but in this case the access point will dynamically shift from 3x4 to 3x3.
Reference: http://www.cisco.com/c/en/us/td/docs/wireless/access_point/2700/quick/guide/ap2700getst art.html