It is more faster and easier to pass the Cisco 300-360 exam by using Simulation Cisco Designing Cisco Wireless Enterprise Networks questuins and answers. Immediate access to the Up to date 300-360 Exam and find the same core area 300-360 questions with professionally verified answers, then PASS your exam with a high score now.
Q21. An engineer is planning for a 24 Mbps data rate for a new installation. What is the coverage area from the AP if the environment and other factors are not taken into consideration?
A. 225 feet
B. 80 feet
C. 150 feet
D. 100 feet
Answer: A
Q22. A hospital environment was designed to guarantee RF coverage at or better than -67 dBm in the 5 GHz spectrum. The customer mandates that RRM be used for DCA and TPC in both bands. After deployment, why do many of the legacy 802.11b/g devices have difficulty maintaining connectivity?
A. Excessive co-channel interference in the 2.4 GHz band exists.
B. Excessive overlapping channels in the 2.4 GHz band exists.
C. TPC drastically reduces Tx power in the 2.4 GHz band.
D. TCP drastically increases Tx power in the 2.4 GHz band.
Answer: C
Q23. Refer to the exhibit.
While testing the post-deployment WLAN network, you discover that an AP has been placed in a difficult area.
The AP cannot be moved easily because of various requirements. The client performance of various Apple and Microsoft operating system-based products does not meet expectations. Which two options can help mitigate the performance issue? (Choose two.)
A. Add additional APs.
B. Increase the AP power level to maximum.
C. Rotate the AP 90 degrees to change antenna polarity.
D. Replace the AP with an AP and external antenna.
E. Change the AP location to one that is less RF hostile.
Answer: A,D
Q24. An engineer must design wireless coverage in thick-walled stairwells. Which information should the engineer refer to when determining where APs can be installed?
A. Local or National Building Code
B. IEEE
C. BICSI TDMM
D. Cisco Hardware Installation Guide
Answer: D
Q25. Which list of characteristics must all controllers in a mobility group have in common based on best practices?
A. mobility group name, version of controller code, Control and Provisioning of Wireless Access Points mode,ACLs, and WLANs (SSIDs)
B. mobility domain name, version of controller code, and Control and Provisioning of Wireless Access Pointsmode
C. mobility domain name, version of controller code, Control and Provisioning of Wireless Access Pointsmode, ACLs, and WLANs (SSIDs)
D. mobility group name, version of controller code, and Control and Provisioning of Wireless Access Pointsmode
Answer: A
Q26. A cabling contractor is working at a customer facility. The contractor is asking what rating of cable should be installed in return-air areas. Which information can be referenced to provide the contractor the requested information?
A. OSHA Codes
B. BICSI TDDM
C. NEC Ratings
D. IEEE Standards
Answer: B
Q27. An engineer must perform a survey where the target client devices range from standard
Wi-Fi-equipped laptops, consumer handhelds and tablets, and low power tracking tags limited to 12 mW Tx power. With which setting should the survey AP be configured?
A. local power 11
B. local power 5
C. local power 14
D. local power 8
Answer: B
Q28. When conducting a wireless survey at a customer facility, signal attenuation in an area that is surrounded by thick glass walls is noted as 2dB. When configuring Cisco Prime Infrastructure, which obstacle should be placed in a map editor to represent the impact the glass wall will have on the RF signal in the facility?
A. heavy door
B. thick wall
C. glass
D. light wall
Answer: D
Explanation: Reference: http://www.cisco.com/c/en/us/td/docs/wireless/prime_infrastructure/1-2/configuration/guide/pi_12_cg/maps.html Table 6-4
Q29. When designing a WLAN, AP placement is important. Which option describes how to rank the density of APs needed to support location services versus data and voice services?
A. Data services have the lowest density of APs compared to location services, which has the highest density.
B. Data services have a lower density of APs compared to location services, but more than voice.
C. Voice services have the highest density of APs over location and data services.
D. Voice and data services require a higher density of APs than location services.
Answer: A
Q30. An engineer is preparing for an indoor wireless LAN survey and is provisioning a survey kit. Which three pieces of equipment should be included? (Choose three.)
A. external connector access point
B. integrated antenna access point
C. coax low-loss cable
D. battery operated power supply
E. range finder
F. Yagi antennas
Answer: B,D,E