It is more faster and easier to pass the Cisco 400 101 pdf exam by using High quality Cisco CCIE Routing and Switching (v5.0) questuins and answers. Immediate access to the Leading 400 101 ccie Exam and find the same core area 400 101 dumps questions with professionally verified answers, then PASS your exam with a high score now.
Q451. Which option describes a limitation of Embedded Packet Capture?
A. It can capture data only on physical interfaces and subinterfaces.
B. It can store only packet data.
C. It can capture multicast packets only on ingress.
D. It can capture multicast packets only on egress.
Answer: C
Explanation:
Restrictions for Embedded Packet Capture
. In Cisco IOS Release 12.2(33)SRE, EPC is supported only on 7200 platform.
. EPC only captures multicast packets on ingress and does not capture the replicated packets on egress.
. Currently, the capture file can only be exported off the device; for example, TFTP or FTP servers and local disk.
Reference: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/epc/configuration/15-mt/epc-15-mt-book/nm-packet-capture.html
Q452. Which statement about LISP encapsulation in an EIGRP OTP implementation is true?
A. OTP uses LISP encapsulation for dynamic multipoint tunneling.
B. OTP maintains the LISP control plane.
C. OTP uses LISP encapsulation to obtain routes from neighbors.
D. LISP learns the next hop.
Answer: A
Q453. Two routers are trying to establish an OSPFv3 adjacency over an Ethernet link, but the adjacency is not forming. Which two options are possible reasons that prevent OSPFv3 to form between these two routers? (Choose two.)
A. mismatch of subnet masks
B. mismatch of network types
C. mismatch of authentication types
D. mismatch of instance IDs
E. mismatch of area types
Answer: D,E
Explanation:
An OSPFv3 interface must have a compatible configuration with a remote interface before the two can be considered neighbors. The two OSPFv3 interfaces must match the following criteria:
. Hello interval
. Dead interval
. Area ID
. Optional capabilities
The OSPFv3 header includes an instance ID field to identify that OSPFv3 packet for a particular OSPFv3 instance. You can assign the OSPFv3 instance. The interface drops all OSPFv3 packets that do not have a matching OSPFv3 instance ID in the packet header.
Reference: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/5_x/nx-os/unicast/configuration/guide/l3_cli_nxos/l3_ospfv3.html
Q454. Which type of OSPF packet is an OSPF link state update packet?
A. type 1
B. type 2
C. type 3
D. type 4
E. type 5
Answer: D
Explanation:
Link State Update packets are OSPF packet type 4. These packets implement the flooding of link state advertisements. Each Link State Update packet carries a collection of link state advertisements one hop further from its origin. Several link state advertisements may be included in a single packet.
Reference: http://www.freesoft.org/CIE/RFC/1583/107.htm
Q455. Refer to the exhibit.
While troubleshooting high CPU utilization on one of your Cisco Catalyst switches, you find that the issue is due to excessive flooding that is caused by STP. What can you do to prevent this issue from happening again?
A. Disable STP completely on the switch.
B. Change the STP version to RSTP.
C. Configure PortFast on port-channel 1.
D. Configure UplinkFast on the switch.
E. Configure PortFast on interface Gi0/15.
Answer: E
Explanation:
Topology Changes (TC) should be a rare event in a well-configured network. When a link on a switch port goes up or down, there is eventually a TC, once the STP state of the port is changing to or from forwarding. When the port is flapping, this would cause repetitive TCs and flooding.
Ports with the STP portfast feature enabled will not cause TCs when going to or from the forwarding state. The configuration of portfast on all end-device ports (such as printers, PCs, and servers) should limit TCs to a low amount and is highly recommended.
Reference: http://www.cisco.com/c/en/us/support/docs/lan-switching/spanning-tree-protocol/28943-170.html
Q456. Which two solutions can reduce UDP latency? (Choose two.)
A. fast retransmission
B. fast recovery
C. fast start
D. low-latency queuing
E. IP service level agreements
F. congestion-avoidance algorithm
Answer: D,E
Explanation:
IP SLA uses active traffic monitoring, which generates traffic in a continuous, reliable, and predictable manner to measure network performance. IP SLA sends data across the network to measure performance between multiple network locations or across multiple network paths. It simulates network data and IP services, and collects network performance information in real time. This information is collected:
Response times
One-way latency, jitter (interpacket delay variance)
Packet loss
Network resource availability
LLQ uses the priority command. The priority command allows you to set up classes based on a variety of criteria (not just User Datagram Ports (UDP) ports) and assign priority to them, and is available for use on serial interfaces and ATM permanent virtual circuits (PVCs). A similar command, the ip rtp priority command, allows you to stipulate priority flows based only on UDP port numbers. Note: All the other answer choices can be used to improve TCP performance, but not UDP.
References: http://www.cisco.com/c/en/us/td/docs/routers/xr12000/software/xr12k_r4-2/system_monitoring/configuration/guide/b_sysmon_cg42xr12k/b_sysmon_cg42xr12k_chapter_011.html http://www.cisco.com/c/en/us/td/docs/ios/12_0s/feature/guide/fsllq26.html
Q457. Refer to the exhibit.
How can the EIGRP hello and hold time for Gig0/0 be changed to 5 and 15?
A. No action is required, since Gig0/0 is not listed with a nondefault hello and hold time.
B. Add the commands ip hello-interval eigrp 1 5 and ip hold-time eigrp 1 15 under interface Gig0/0.
C. Add the commands hello-interval 5 and hold-time 15 under "af-interface Gig0/0" under the address family.
D. Add the commands default hello-interval and default hold-time under the af-interface Gig0/0 statement under the address family.
Answer: C
Explanation:
To configure the hello interval for an interface, use the hello-interval command in interface configuration mode To configure the hold time for an interface, use the hold-time command in interface configuration mode.
Reference: http://www.cisco.com/c/en/us/td/docs/routers/crs/software/crs_r4-1/routing/command/reference/b_routing_cr41crs/b_routing_cr41crs_chapter_010.html#wp2 323069468
Q458. DRAG DROP
Drag and drop the path-selection criteria on the left into the correct route-selection order on the right, that a router will use when having multiple routes toward the same destination.
Answer:
Q459. An IP SLA fails to generate statistics. How can you fix the problem?
A. Add the verify-data command to the router configuration.
B. Reload the router configuration.
C. Remove the ip sla schedule statement from the router configuration and re-enter it.
D. Add the debug ip sla error command to the router configuration.
E. Add the debug ip sla trace command to the router configuration.
Answer: A
Q460. Which two statements best describes the difference between active mode monitoring and passive mode monitoring? (Choose two.)
A. Active mode monitoring is the act of Cisco PfR gathering information on user packets assembled into flows by NetFlow.
B. Active mode monitoring uses IP SLA probes for obtaining performance characteristics of the current exit WAN link.
C. Passive mode monitoring uses IP SLA to generate probes for the purpose of obtaining information regarding the characteristics of the WAN links.
D. Passive mode monitoring uses NetFlow for obtaining performance characteristics of the exit WAN links.
Answer: B,D