Exam Code: cisco 400 101 (Practice Exam Latest Test Questions VCE PDF)
Exam Name: CCIE Routing and Switching (v5.0)
Certification Provider: Cisco
Free Today! Guaranteed Training- Pass 400 101 vce Exam.
Q391. DRAG DROP
Answer:
Q392. Which two options are valid for the number of bytes in a BGP AS number? (Choose two.)
A. 2 bytes
B. 4 bytes
C. 6 bytes
D. 8 bytes
E. 16 bytes
Answer: A,B
Explanation:
During the early time of BGP development and standardization, it was assumed that availability of a 16 bit binary number to identify the Autonomous System (AS) within BGP would have been more than sufficient. The 16 bit AS number, also known as the 2-byte AS number, provides a pool of 65536 unique Autonomous System numbers. The IANA manages the available BGP Autonomous System Numbers (ASN) pool, with the assignments being carried out by the Regional Registries. The current consumption rate of the publicly available AS numbers suggests that the entire public 2-byte ASN pool will be fully depleted. A solution to this depletion is the expansion of the existing 2-byte AS number to a 4-byte AS number, which provides a theoretical 4,294,967,296 unique AS numbers. ARIN has made the following policy changes in conjunction with the adoption of the solution. The Cisco IOS BGP "4-byte ASN" feature allows BGP to carry a Autonomous System Number (ASN) encoded as a 4-byte entity. The addition of this feature allows an operator to use an expanded 4-byte AS number granted by IANA.
Q393. Refer to the exhibit.
Which two statements are true regarding prefix 10.1.0.0/24? (Choose two.)
A. The prefix is in policy, and Cisco PfR rerouted the traffic via 10.4.5.3 Et0/1 because of an OOP event.
B. Cisco PfR is monitoring the prefix via passive NetFlow mode only.
C. Cisco PfR is monitoring the prefix via active, fast, or active throughput IP SLA probe mode only.
D. The prefix is in policy, and Cisco PfR did not reroute the traffic via 10.4.5.3 Et0/1 because the traffic was previously in policy.
E. Cisco PfR is monitoring the prefix via mode monitor, which provides both NetFlow and IP SLA measurements.
Answer: D,E
Reference: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/pfr/command/pfr-cr-book/pfr-s1.html#wp2707728086
Q394. Which two statements about IP SLAs are true? (Choose two.)
A. They are Layer 2 transport independent.
B. Statistics are collected and stored in the RIB.
C. Data for the delay performance metric can be collected both one-way and round-trip.
D. Data can be collected with a physical probe.
E. They are used primarily in the distribution layer.
Answer: A,E
Q395. Which TCP mechanism prevents the sender from sending data too quickly for the receiver to process?
A. Congestion control
B. Error detection
C. Selective acknowledgement
D. Flow control
Answer: D
Explanation:
In data communications, flow control is the process of managing the rate of data transmission between two nodes to prevent a fast sender from overwhelming a slow receiver. It provides a mechanism for the receiver to control the transmission speed, so that the receiving node is not overwhelmed with data from transmitting node.
Reference: http://en.wikipedia.org/wiki/Flow_control_(data)
Q396. Refer to the exhibit.
If the downstream router has a summary route configured, which two actions must you take on the local router to create the summary route that summarizes all routes from the downstream router? (Choose two.)
A. Configure the summary address on the interface.
B. Use 10.0.0.0 255.248.0.0 as the summary route.
C. Configure the summary address in the EIGRP process.
D. Use 10.0.0.0 255.252.0.0 as the summary route.
E. Configure a route map to permit the route.
F. Configure a distribute list in.
Answer: A,B
Explanation:
Route summarization works in conjunction with the ip summary-address eigrp interface configuration command, in which additional summarization can be performed. To correctly summarize all the networks shown, the correct route to use is 10.0.0.0 255.248.0.0
Reference: http://www.cisco.com/c/en/us/td/docs/ios/12_2/ip/configuration/guide/fipr_c/1cfeigrp.html
Q397. Refer to the exhibit.
RIPv2 authentication is failing on a device with this configuration. Which two actions can you take to enable it? (Choose two.)
A. Set the RIP authentication mode to text.
B. Set the RIP authentication mode to MD5.
C. Configure the password encryption for the key.
D. Set the password encryption to AES.
Answer: A,B
Explanation:
See the reference link below for information on configuring RIPv2 authentication, including both test and MD5 modes.
Reference: http://www.cisco.com/c/en/us/support/docs/ip/routing-information-protocol-rip/13719-50.html#configuringplain
Q398. Which three statements are true about an EtherChannel? (Choose three.)
A. PAGP and LACP can be configured on the same switch if the switch is not in the same EtherChannel.
B. EtherChannel ports in suspended state can receive BPDUs but cannot send them.
C. An EtherChannel forms between trunks that are using different native VLANs.
D. LACP can operate in both half duplex and full duplex, if the duplex setting is the same on both ends.
E. Ports with different spanning-tree path costs can form an EtherChannel.
Answer: A,B,E
Explanation:
Answer A. EtherChannel groups running PAgP and LACP can coexist on the same switch or on different switches in the stack. Individual EtherChannel groups can run either PAgP or LACP, but they cannot interoperate.
Answer B:
EtherChannel Member Port States
Port States
Description
bundled
The port is part of an EtherChannel and can send and receive BPDUs and data traffic.
suspended
The port is not part of an EtherChannel. The port can receive BPDUs but cannot send them. Data traffic is blocked.
standalone
The port is not bundled in an EtherChannel. The port functions as a standalone data port. The port can send and receive BPDUs and data traffic.
Answer E. Ports with different spanning-tree path costs can form an EtherChannel if they are otherwise compatibly configured. Setting different spanning-tree path costs does not, by itself, make ports incompatible for the formation of an EtherChannel.
Reference: http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960x/software/15-0_2_EX/layer2/configuration_guide/b_lay2_152ex_2960-x_cg/b_lay2_152ex_2960-x_cg_chapter_010.html
Q399. Which Cisco IOS VPN technology leverages IPsec, mGRE, dynamic routing protocol, NHRP, and
Cisco Express Forwarding?
A. FlexVPN
B. DMVPN
C. GETVPN
D. Cisco Easy VPN
Answer: B
Q400. What can PfR passive monitoring mode measure for TCP flows?
A. only delay
B. delay and packet loss
C. delay and reachability
D. delay, packet loss, and throughput
E. delay, packet loss, throughput, and reachability
Answer: E
Explanation:
Passive monitoring metrics include the following:
. Delay: Cisco PfR measures the average delay of TCP flows for a given prefix or traffic class. Delay is the measurement of the round-trip response time (RTT) between the transmission of a TCP synchronization message and receipt of the TCP acknowledgement.
. Packet loss: Cisco PfR measures packet loss by tracking TCP sequence numbers for each TCP flow; it tracks the highest TCP sequence number. If it receives a subsequent packet with a lower sequence number, PfR increments the packet-loss counter. Packet
loss is measured in packets per million.
. Reachability: Cisco PfR measures reachability by tracking TCP synchronization messages that have been sent repeatedly without receiving a TCP acknowledgement.
. Throughput: Cisco PfR measures TCP throughput by measuring the total number of bytes and packets for each interesting traffic class or prefix for a given interval of time.
Reference: http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/performance-routing-pfr/product_data_sheet0900aecd806c4ee4.html