Master the ccie 400 101 CCIE Routing and Switching (v5.0) content and be ready for exam day success quickly with this Exambible passleader 400 101 test. We guarantee it!We make it a reality and give you real 400 101 pdf questions in our Cisco cisco 400 101 braindumps.Latest 100% VALID Cisco 400 101 pdf Exam Questions Dumps at below page. You can use our Cisco cisco 400 101 braindumps and pass your exam.

P.S. Practical 400-101 preparation labs are available on Google Drive, GET MORE: https://drive.google.com/open?id=10qRl3c2aPM7jDirL_NepQ9ytoJQZm2pM


New Cisco 400-101 Exam Dumps Collection (Question 13 - Question 20)

Q13. Refer to the exhibit.

Which effect of this configuration is true?

A. Users can enter user EXEC mode without a user name using password cisco4

B. Users in user EXEC mode can enter privileged EXEC mode without a user name or password.

C. Users can enter privileged EXEC mode using user name ciscol and password cisco2

D. Users in user EXEC mode can enter privileged EXEC mode without a user name using password

Answer: C


Q14. ON NO: 402

Refer to the exhibit.

Which two statements about the output are true? (Choose two.)

A. 802.1D spanning tree is being used.

B. Setting the priority of this switch to 0 for VLAN 1 would cause it to become the new root.

C. The hello, max-age, and forward delay timers are not set to their default values.

D. Spanning-tree PortFast is enabled on GigabitEthernet1/1.

Answer: A,B

Explanation:

802.1D is the standard for Spanning tree, which is being used here. For priority, The priority order starts from 0 (yes, 0 is valiD. and then increases in 4096.

0, 4096, 8192, 12288, u2026. Etc.

The lower the number is, the higher is the priority. Here we see that the current root has a priority of 8192, so configuring this with a priority of 0 will make it the new root.


Q15.

Refer to exhibit. R1, R2, and R3 are in different statellite offices of the same organization. A multiast vido source is located behind R1. R3 frequently receives video streams interded for R2. These streams saturate the available bandwidth of R3. Which configuration change can alleviate the congestion on R3?

A. Configure R3 to send an immediate-leave message when necessary 10 stop receiving unwanted traffic

B. Configure IGMP snooping on R1 R 2 and R3

C. Place a PIM filter u00f3n the switches and interfaces that connect 10 R1R2 and R3

D. Enable IGMP snooping On all switches that contect to R1 R2 and R3

E. Place a PIM filter on the switch and interface that connect to R1 only

Answer: D


Q16. How does an IPv6 host automatically genu00e8rate a global address?

A. It prepends its interface identifier to the network prefixs contained in Router Advertisement messages

B. It appends its interface identifier to the network prefixs contained in Router Advertisement messages

C. It appends its interface identifier to the network prefixs contained in Router Solicitation

messag s

D. It prepends its interface identifier to the network prefixs contained in Router Solicitation messages

Answer: B

Explanation: QUESTIO.N 7

Which statement about the feasible distance in EIGRP is true?

A. It is metric that is support by the best next hop toward the destination

B. It is the maximum metric that should feasibly be considered for installation in the RIB C.It is the smallest metric toward the destination enc'OuntereD... ... time the destination went from Active to Passive state

D.It is the maximum metric possible based on the maximum hop count that is allowed Answer: C


Q17. Which feature can you implement to reduce global synchronization?

A. marking

B. NBAR

C. WRED

D. policing

Answer: C


Q18. In a simple MPLS L3VPN, which two tasks are performed by the PE router? (Choose two.)

A. It establishes pseudo wires with other PEs.

B. It exchanges VPNv4 and VPNv6 routes with CE Devices.

C. It assigns labels to routes in individual VPNs.

D. It forwards labeled packets to CE devices.

E. It exchanges VPNv4 or VPNv6 route with other PE routers.

Answer: C,E


Q19. If the default-information originate always command is configured on R4 what route type is assigned to the default route in R1's

A. O

B. E2

C. O IA

D. E1

Answer: C


Q20. How does EIGRP derive the metric for manual summary routes ?

A. It uses the worst metric vectors of all component routes in the topology table.

B. It uses the best metric vectors of all component routes in the topology table.

C. It uses the best composite metric of any component route in the topology table

D. It uses the worst composite metric of any component route in the topology table

Answer: C


Recommend!! Get the Practical 400-101 dumps in VCE and PDF From Surepassexam, Welcome to download: https://www.surepassexam.com/400-101-exam-dumps.html (New 911 Q&As Version)