To this particular Juniper JN0-533 examination isnt a difficult job. You just have a need to look at selected actions connected with obtaining positive results. Ucertify JN0-533 recognition exercise fabric are useful trying to keep a persons preparing very efficient or longer to your make. Were offering 100% guaranteed achievement inside JN0-533 true examination along with JN0-533 when using the aid of the exercise examination. Therefore by means of training the JN0-533 training fabric, get those essential recognition and strive to are a greatest IT specialized.
2021 Nov JN0-533 brain dumps
Q1. You have enabled BGP on your ScreenOS device and configured a single EBGP peer. The CLI shows that the BGP connection is transitioning between the CONNECT and ACTIVE states, but never reaching the ESTABLISHED state.
What are three reasons for this behavior? (Choose three.)
A. The peer is blocking traffic destined for TCP port 179.
B. The peer address is not configured correctly.
C. The enable statement has not been configured for the peer.
D. The peer AS number is not configured correctly.
E. BGP has not been enabled on the virtual router.
Answer: A,B,D
Q2. You have just installed a new ScreenOS device in your network and you want only a select range of IP addresses to have administrative access to the device.
Which choice will allow you to accomplish this?
A. Configure a manager IP.
B. Configure the management interface.
C. Configure a management IP on the trust interface.
D. Configure new system administrators.
Answer: A
Q3. HostA is in the Trust zone and has an IP address of. ServerA is a Web server in the DMZ zone and has an IP address of.
Which three configuration statements are required to allow traffic from HostA to communicate with ServerA? (Choose three.)
A. ssg5-> set address Trust HostA /32
B. ssg5-> set policy from DMZ to Trust ANY ANY ANY permit
C. ssg5-> set address DMZ ServerA /32
D. ssg5-> set policy from Trust to DMZ HostA ServerA HTTP permit
E. ssg5-> set address Trust HostA /32
Answer: C,D,E
Q4. What are two advantages for using the count parameter on a security policy? (Choose two.)
A. to see any NAT traffic drops for that policy
B. to see how many times users log in to the ScreenOS device
C. to count the total number of bytes of traffic for that policy
D. to see if the policy is temporarily not being used
Answer: C,D
Q5. You have configured a single-port VIP to forward HTTP traffic from the untrust interface on your ScreenOS device to an internal Web server. You have configured a policy to allow this traffic. Traffic from the untrust interface that matches this policy is unable to connect to the Web server. What is a solution to this problem?
A. You must reboot the ScreenOS device for the VIP to become active.
B. You must ensure the ScreenOS device has a route to the Web server.
C. You must ensure the Web server is directly connected to the ScreenOS device.
D. You must save the ScreenOS device configuration for the VIP to become active.
Answer: B
Most recent JN0-533 rapidshare:
Q6. Click the Exhibit button.
Referring to the exhibit, what is the appropriate VPN monitor status?
A. The VPN is active and the peer is down.
B. The VPN is active and VPN Monitor is not configured for the peer.
C. The VPN is active and the peer is up.
D. The VPN is inactive and VPN Monitor is not configured for the peer.
Answer: B
Q7. -- Exhibit -- set admin name "admin" set admin password "nOsYMqrbAs/McFsJrs6HwcIt3AF6yn" set admin user "User1" password "nLZwKErINPPCcphC6sFMXrJ" privilege "read-only" set admin port 8080 set admin access attempts 5 set admin access lock-on-failure 5 set admin auth web timeout 10 set admin auth server "Local" -- Exhibit --
User1 wants to create the policy in the ScreenOS device, but is not successful.
Referring to the exhibit, what is the problem?
A. The User1 account has been suspended.
B. User1 does not have any account in this device.
C. User1 logged in to the device with wrong port.
D. User1 does not have the proper permission to create a policy.
Answer: D
Q8. You are configuring a VPN with IKE between headquarters and a branch office that uses a dynamic public IP address. Which IKE mode should you use?
A. quick mode
B. main mode
C. aggressive mode
D. wizard mode
Answer: C
Q9. You are troubleshooting telnet traffic destined to IP address 10.10.10.1. You decide to run debug and want to set the flow filter. Which command will show only the telnet traffic going to the
10.10.10.1 address?
A. ssg5-serial-> set ffilter dst-ip 10.10.10.1 ssg5-serial-> set ffilter dst-port 23
B. ssg5-serial-> set ffilter dst-ip 10.10.10.1 dst-port 23
C. ssg5-serial-> set ffilter dst-port 23
D. ssg5-serial-> set ffilter dst-ip 10.10.10.1
Answer: B
Q10. In a policy, which two statements are true about the no-hw-sess command? (Choose two.)
A. It increases the load on the CPU.
B. It is used for debugging.
C. It increases the load on the ASIC card.
D. It reduces the load on the CPU.
Answer: A,B