Cause all that matters here is passing the Juniper JN0-533 exam. Cause all that you need is a high score of JN0-533 FWV, Specialist (JNCIS-FWV) exam. The only one thing you need to do is downloading Pass4sure JN0-533 exam study guides now. We will not let you down with our money-back guarantee.
2021 Nov JN0-533 training
Q11. Your ScreenOS device is configured with multiple NAT types.
What is the order of precedence in this situation?
A. interface-based NAT -> VIP -> MIP -> policy-based NAT
B. VIP -> MIP -> policy-based NAT -> interface-based NAT
C. MIP -> VIP -> interface-based NAT -> policy-based NAT
D. MIP -> VIP -> policy-based NAT -> interface-based NAT
Answer: D
Q12. You have configured integrated Web filtering in the ScreenOS software. A URL appears in the blacklist, the whitelist, and a user-defined category. Additionally, the device can obtain categorization information from the SurfControl server.
Which configuration will the device use to determine the action to take for Web requests for the URL?
A. the blacklist
B. the SurfControl categorization
C. the user-defined category
D. the whitelist
Answer: A
Q13. An SSG5 has a default configuration loaded on it. Which two statements are correct? (Choose two.)
A. Intrazone blocking is enabled for the trust zone.
B. Intrazone blocking is disabled for the trust zone.
C. Intrazone blocking is enabled for the untrust zone.
D. Intrazone blocking is disabled for the untrust zone.
Answer: B,C
Q14. A monitored interface on a clustered pair of ScreenOS devices goes down and both devices became ineligible to be master of the cluster. As a result, neither device is passing traffic.
Which step would have prevented this situation?
A. Configure initial hold-down time to 10 seconds.
B. Configure the preempt parameter and a higher priority on one of the devices.
C. Configure the lost heartbeat interval to 1 second.
D. Configure the master-always-exists parameter.
Answer: D
Q15. Traffic is not passing the ScreenOS device due to an incorrectly configured policy. You must determine exactly which security policy the traffic is using.
Which two CLI commands should be used? (Choose two.)
A. snoop
B. get session
C. debug flow basic
D. get counter stats
Answer: B,C
Down to date JN0-533 practice question:
Q16. -- Exhibit -- ns5gt-> get int Interfaces in vsys Root: Name IP Address Zone MAC VLAN State VSD eth1 192.168.1.1/24 Trust 0014.f693.edc2 - U -eth2 2.2.2.2/30 Untrust 0014.f693.edc8 - U - ns5gt-> get db stream ****** .0: <Trust/ethernet1> packet received [69]******
ipid = 22281(5709), @059ff214 packet passed sanity check. flow_decap_vector IPv4 process ethernet1:192.168.1.102/52380->4.2.2.2/53,17<Root> no session found flow_first_sanity_check: in <ethernet1>, out <N/A> chose interface ethernet1 as incoming nat if. flow_first_routing: in <ethernet1>, out <N/A> search route to (ethernet1, 192.168.1.102->4.2.2.2) in vr trust-vr for vsd-0/flag-0/ifp-null [ Dest] 7.route 4.2.2.2->2.2.2.1, to ethernet2 routed (x_dst_ip 4.2.2.2) from ethernet1 (ethernet1 in 0) to ethernet2 Permitted by policy 1 dip id = 2, 192.168.1.102/52380->2.2.2.2/2157 choose interface ethernet2 as outgoing phy if no loop on ifp ethernet2. routed (x_dst_ip 4.2.2.2) from ethernet1 (ethernet1 in 0) to ethernet2 policy search from zone 2-> zone 1
-- Exhibit --
Referring to the debug output shown in the exhibit, which NAT configuration is being used?
A. MIP
B. destination-based NAT
C. source-based NAT
D. VIP
Answer: C
Q17. You want to set up a last resort route and prevent route lookups in either the source-based routing table or the destination-based routing table.
What should you do?
A. Disable SIBR and create a default route in the trust-vr table using the null interface as the outgoing interface with a higher metric than other routes.
B. Disable SIBR and create a default route in the trust-vr table using the null interface as the outgoing interface with a lower metric than other routes.
C. Enable SIBR and create a default route in the SIBR table using the null interface as the outgoing interface with a higher metric than other routes.
D. Enable SIBR and create a default route in the SIBR table using the null interface as the outgoing interface with a lower metric than other routes.
Answer: C
Q18. Click the Exhibit button.
Referring to the output shown in the exhibit, which NAT configuration is being used?
A. interface-based NAT
B. DIP
C. source-based NAT
D. VIP
Answer: D
Q19. You have configured integrated Web filtering in the ScreenOS software. You find that users trying to access http://www.example.com are being blocked by your Web-filtering configuration. However, you want all users to be able to access this Web site.
What are two methods to allow this traffic? (Choose two.)
A. Configure an SC-CPA exception for the URL.
B. Configure the URL as part of a custom category and allow requests in that category.
C. Configure the URL as part of the blacklist.
D. Configure the URL as part of the whitelist.
Answer: B,D
Q20. Which two statements are true about VPN Monitor on a ScreenOS device? (Choose two.)
A. With a route-based VPN failure, VPN Monitor marks the tunnel interface status as down.
B. With a policy-based VPN failure, VPN Monitor marks the tunnel interface status as down.
C. VPN Monitor uses UDP to detect a VPN connection failure.
D. VPN Monitor uses ICMP to detect a VPN connection failure.
Answer: A,D