Our This experts dedicate to developing the Juniper JN0-692 on-line questions and answers. You can download the JN0-692 dumps upon our web site. We not merely present the actual Juniper Pdf exams but furthermore the test engine. Our own Juniper Juniper test motor is cutting-edge software which can be built to generate you experience that you tend to be in the real Juniper JN0-692 exam. This will be your enriching and unforgettable experience in your life. You can make your own Juniper JN0-692 preparation at your personal pace and with your own style as a consequence of the flexibility regarding our 2 types of JN0-692 questions. You can put the actual various options and facilities, which usually provided from the Juniper JN0-692 exam engines, into use. Whilst doing your own Juniper JN0-692 practice exams on your JN0-692 exam motor you will experience that your learning rate is enhanced.
2021 Nov JN0-692 free practice test
Q51. You have configured bidirectional LSPs between R1 and R3. You notice that the LSPs are not coming up.
Referring to the exhibit, which statement is correct?
A. You must disable CSPF for the LSPs.
B. You must enable CSPF for the LSPs.
C. You must ensure type 5 LSAs are allowed in area 1.
D. You must ensure OSPF traffic engineering is configured.
Answer: A
Q52. What would happen if the guaranteed-rate command is removed from the configuration shown in the exhibit?
A. The logical interface gets a minimal bandwidth reservation.
B. The minimum-rate command should be configured instead.
C. The logical interface receives no bandwidth constraints.
D. The transmit-rate command should be configured instead.
Answer: A
Q53. Click the Exhibit button.
All routers shown in the exhibit are BGP neighbors. R1 must be a route reflector, and R2 through R5 must be clients. R2 should only receive one copy of all routes sent from R4. Which configuration is valid?
A. Option A
B. Option B
C. Option C
D. Option D
Answer: B
Q54. IS-IS is configured to support both IPv4 and IPv6 routing. Which statement is true?
A. Separate IPv4 and IPv6 hellos will be sent.
B. IPv6 will have a separate link-state database.
C. IS-IS v6 support must be enabled under protocols isis.
D. IS-IS sends IPv6 topology information as new TLVs in existing LSPs.
Answer: D
Q55. A LDP Layer 2 circuit is shown for VPN A and VPN B. LDP tunneling over RSVP is activated on P1 and P2. Referring to the exhibit, which statement is true about the LDP Layer 2 circuit?
A. MAC learning is needed and using the inner VPN label between PE1 and PE2 for VPN A or VPN B.
B. Targeted LDP sessions are established between PE1, P1 and P2, PE2.
C. Label stitching must be configured on P1 and P2 for end to end transport LSPs.
D. LDP must be enabled on the loopback interfaces of PE1 and PE2.
Answer: D
Down to date JN0-692 question:
Q56. Click the Exhibit button.
Customer A is complaining that routes advertised from the CE2 router are not being received on the CE1 router. The physical topology of the network is CE1-PE1-PE2- CE2. The CE1-PE1 subnet is 172.16.1.0/24. The CE2-PE2 subnet is 172.16.2.0/24.
PE1's loopback is 192.168.3.1 and PE2's loopback is 192.168.4.1.Referring to the output in the exhibit, what is the problem?
A. No LSP exists between PE1 and PE2.
B. Route targets are not properly configured.
C. as-override is not configured in the VRFs.
D. family inet-vpn is not configured on the PEs.
Answer: C
Q57. Click the Exhibit button.
R3 and R4 want to establish an EBGP session between each other's loopback addresses. They have each configured static routes to the other's loopback address and can ping from loopback to loopback. Their EBGP session is configured with correct neighbor and local addresses. The correct AS numbers have been specified at the [routing-options] hierarchy as well. Considering the topology in the exhibit, which statement is true?
A. BGP's protocol preference must be adjusted to be lower than protocol static for the session to establish.
B. Each side must configure multipath for the session to establish.
C. Each peer must specify a local-as within their EBGP configuration for the session to establish.
D. Each peer must configure multihop for the session to establish.
Answer: D
Q58. Based on the exhibit, what do you expect to find in the configuration on R1 and R4?
A. a policy leaking level 1 routes into level 2
B. a policy leaking level 2 routes into level 1
C. a policy setting the attached bit on level 2 routes
D. a policy setting the attached bit on level 1 routes
Answer: B
Q59. Click the Exhibit button.
The exhibit contains a BGP topology. R1 and R2 are peering using IBGP. R2 and R3 are peering with EBGP. R1 is not installing any routes from R3 due to next-hop resolution issues. Which two configurations will resolve this issue? (Choose two.)
A. Use a policy to advertise the loopback on R2 into the IGP.
B. Advertise the R2-R3 subnet into the IGP.
C. Configure advertise-inactive on the IBGP peering session on R2.
D. Configure next-hop self on the IBGP peering session on R2.
Answer: B, D
Q60. You manage an MPLS network. You are asked to classify traffic using the EXP bits from ingress to egress. What will allow you to accomplish this?
A. Configure explicit-null on the penultimate router.
B. Configure explicit-null on the egress router.
C. Configure implicit-null on the penultimate router.
D. Configure implicit-null on the egress router.
Answer: B