While you convey a Juniper on your set of skills, itll very first benefit you by just helping replace your operate circulation. Through advancing your understanding bottom part, you will find a more effective perception of what you are doing and also operate more expeditiously. Further, you should understand on your path round the software as good as a good number of, which could often let you discover the best and a lot of helpful means for that you complete ones assignments. But it surely doesn?¡¥t purely end using very own efficiency degrees and also figuring out all to know about Juniper techniques.

2021 Nov JN0-692 practice

Q21. Given the topology in the exhibit, which two requirements must be met to allow multicast traffic to flow from AS65001 to AS65002? (Choose two.) 

A. MSDP sessions must exist between all routers in AS65001. 

B. Source information must be relayed from AS65001 to AS65002. 

C. A full mesh of MBGP peering sessions must be formed within AS65001. 

D. A TCP session must be formed between the RPs in AS65001 andAS65002. 

Answer: B, D 


Q22. Which two scenarios would explain the error shown in the exhibit? (Choose two.) 

A. Packets were dropped in the receive path of the local router. 

B. The local router received a route withdrawal from the peer. 

C. Packets were dropped in the receive path of the peer router. 

D. The local router egress interface towards the peer was congested. 

Answer: C, D 


Q23. R2 and R3 advertise a default route into Area 1.Based on the configurations in the exhibit, which statement is true? (Choose two.) 

A. Traffic from R1 to internal OSPF destinations in Area 0 will always transit R4. 

B. Traffic from R1 to internal OSPF destinations in Area 0 will always transit R2. 

C. Traffic from R1 to external OSPF destinations in Area 0 will always transit R2. 

D. Traffic from R1 to external OSPF destinations in Area 0 will always transit R4. 

Answer: A, C 


Q24. You are adding nonforwarding route reflectors to your network. Which three actions ensure that VPN routes are advertised properly? (Choose three.) 

A. Use rib-groups to add IGP routes to inet.3 and/or inet6.3 on the route reflectors. 

B. Add MPLS LSPs between the route reflectors and their client routers. 

C. Add the route reflectors to the same IGP domain as their clients. 

D. Use rib-groups to add VPN routes to inet.0 and/or inet6.0 on the route reflectors. 

E. Add a static default route to inet.3 and/or inet6.3 on the route reflectors. 

Answer: A, B, E 


Q25. The 10.200/16 network is announced as an IS-IS route by R2 to its IS-IS neighbors. R3 and R4 are configured with an IS-IS export policy, which announces this route to R5 and R6. Which statement is true? 

A. When viewed on R5 the 10.200/16 route will be marked down. 

B. When viewed on R5 the 10.200/16 route will be marked up. 

C. The 10.200/16 route will not be visible on R5. 

D. The 10.200/16 route will be marked with the overload bit. 

Answer: A 


Renewal JN0-692 exam answers:

Q26. In the exhibit, R1 has a loopback address of 192.168.1.1. Its loopback interface is included in OSPF Area 1.Which two statements are true? (Choose two.) 

A. R1 will advertise the loopback address in a Type 1 LSA. 

B. R1 will advertise the loopback address in a Type 3 LSA. 

C. Area 0 will see the loopback address in a Type 1 LSA. 

D. Area 0 will see the loopback address in a Type 3 LSA. 

Answer: A, D 


Q27. Based on the output shown in the exhibit, which statement is correct? 

A. R3 is the designated intermediate system. 

B. R3 is the backup designated intermediate system. 

C. R3 has been configured with an export policy and is announcing external routes to IS-IS neighbors. 

D. R3 is using both IPv4 and IPv6 resulting in two pseudonodes. 

Answer: A 


Q28. Traffic is flowing through the interfaces in the exhibit as follows: 

On ge-0/0/2.0, IPv4 traffic has a throughput rate of 4 Mbps, and the burst size counter is at 200 KB. 

On ge-0/0/2.0, IPv6 traffic has a throughput rate of 7 Mbps, and the burst size counter is at 550 KB. 

On ge-0/0/3.0, IPv4 traffic has a throughput rate of 5 Mbps, and the burst size counter is at 250 KB. 

On ge-0/0/3.1, IPv6 traffic has a throughput rate of 12 Mbps, and the burst size counter is at 450 KB. 

Which statement describes what is happening? 

A. IPv6 traffic on ge-0/0.3.1 is being dropped; all other traffic is unaffected. 

B. IPv4 traffic on ge-0/0/2.0 is unaffected; IPv6 traffic on ge-0/0/2.0 is being dropped; IPv4 traffic on ge-0/0/3.0 is unaffected; IPv6 traffic on ge-0/0/3.1 is being dropped. 

C. IPv4 traffic on ge-0/0/2.0 is being dropped; IPv6 traffic on ge-0/0/2.0 is being dropped; IPv4 traffic on ge-0/0/3.0 is unaffected; IPv6 traffic on ge-0/0/3.1 is unaffected. 

D. All IPv4 and IPv6 traffic on ge-0/0/2 and ge-0/0/3 is being dropped. 

Answer: B 


Q29. Click the Exhibit button. 

You work for ISP A. Customers of both ISP B and ISP C must be able to reach all of your customers, but your network must not allow transit traffic between ISP B and ISP C. 

Referring to the exhibit, which two methods could you use? (Choose two.) 

A. Use local preference to prefer the proper routes. 

B. Use the well-known no-transit community. 

C. Use policy to filter routes on AS number. 

D. Use communities to identify and filter routes. 

Answer: C, D 


Q30. You have configured an IS-IS adjacency between routers R1 and R2. However, the adjacency is not coming up. Referring to the exhibit, what appears to be the problem? 

A. The R2 interface is down. 

B. The ge-1/1/2.0 interface has IS-IS level 2 disabled. 

C. The ge-1/1/2.0 interface does not have family iso configured. 

D. The ge-1/1/2.0 interface has IS-IS level 1 disabled. 

Answer: C