Top Quality of 199-01 pdf exam materials and free demo for Riverstone certification for IT specialist, Real Success Guaranteed with Updated 199-01 pdf dumps vce Materials. 100% PASS Riverbed Certified Solutions Professional exam Today!
Q76. The exhibit shows a data center side serial clustering deployment. In this organization, not every remote site has a Steelhead appliance deployed, and all remote locations will be connecting to the data center.
For connections initiated from the data center, there is a possibility that the Steelhead appliances shown in the exhibit will end up peering with each other, rather than the intended remote Steelhead appliances. Where are peering rules needed to prevent this problem?
A. A only
B. B only
C. B and C
D. A and B
Answer: D
Q77. The Interceptor appliance will attempt to redirect a connection to a Steelhead appliance in the auto pool:
A. When no user defined Load Balancing rules matches AND peer neighbors are defined
B. When no user defined Load Balancing rules matches AND no peer neighbors are defined
C. When no peer Interceptor appliances are defined
D. When a user-defined Load Balancing rule matches AND a target Steelhead appliance is available
Answer: A
Q78. The default setting for "allow failure" in the Interceptor appliance version 2.0 is: (Select 2)
A. Is configurable
B. Is not configurable
C. Enabled by default
D. Disabled by default
Answer: AD
Q79. Which of the following interfaces should be used for datastore synchronization? (Select 2)
A. inpath0_0
B. inpath0_1
C. Primary
D. AUX
Answer: CD
Q80. What platform is supported by SMC-VE?
A. ESX 3.5
B. ESX 4.0
C. ESX 4.1
D. RSP
E. HyperV
Answer: D
Q81. In a new in-path deployment, connections are listed as pass-through on the branch office Steelhead appliance. Which of the following is the likely cause of the problem?
1) Pass-through rule preventing optimization
2) Server-side Steelhead appliance is down
3) Satellite proxy not copying auto-discovery probes
4) Asymmetric routing is detected for the client/server flow
5) Duplex mismatch on WAN or LAN interface
A. 3, 2
B. 2, 4
C. 1, 2, 5
D. 1, 2, 3, 4
E. 1, 2, 3, 4, 5
Answer: D
Q82. Refer to the exhibit.
Corp-A and Corp-B have overlapping address space and therefore the network administrator implemented NAT to overcome this. Users from Corp-A NAT to 172.16.1.0/24 and users from Corp-B NAT to 172.16.2.0/24. Users in Corp-A use the destination address of 172.16.2.0/24 to access the resources in Corp-B. The servers in Corp-B use the client IP for authentication. What do you need to do in order to make this deployment work? (Select 2)
A. Configure Full Transparency
B. Configure out-of-path
C. Configure Port Transparency
D. Configure OOB Transparency
E. Steelhead appliances cannot be deployed in this network
Answer: AD
Q83. A deployment has two parallel Interceptor appliances (A and B) each across a different link directed at different data center locations. Each data center has one Steelhead appliance (Steelhead-1 or Steelhead-2). The administrator wants probes coming into Interceptor A to be first serviced by Steelhead-1, then Steelhead-2 only if Steelhead-1 is full or unavailable. What is the most appropriate rule to be configured?
A. A Redirect Load Balancing rule containing Steelhead-1 and Steelhead-2
B. No Load Balancing rules are needed for the administrator's policy
C. Two Redirect Load Balancing rules; first rule for Steelhead-1 and second rule for Steelhead-2
D. Two Redirect Load Balancing rules; first for both Steelhead-1 and Steelhead-2, second one for Steelhead-2
Answer: C
Q84. In the exhibit,
Where should the WCCP redirection take place for traffic originating from the clients to the servers, assuming redirect IN is used?
A. A
B. B
C. C
D. D
E. E
Answer: A
Q85. In the exhibit,
Which interfaces should the WCCP router R1 listen to for multicast communication with the server- side Steelhead appliances, assuming the multicast address is 239.0.0.1? (Select 2)
A. A
B. B
C. C
D. D
E. E
Answer: DE
Q86. Which user roles and permissions are supported by the CMC appliance? (Select 3)
A. Read-Only
B. Read/Write
C. Write-Only
D. Deny
E. Accept
Answer: ABD
Q87. What are the default port labels on an Interceptor appliance?
A. Optimized, Pass-through, Blocked
B. Interactive, RBT-Proto, Secure
C. RBT-Proto, Enabled, Disabled
D. Named differently from those on the Steelhead appliance
E. Port labels do not exist on an Interceptor appliance
Answer: B
Q88. The port used by the Steelhead appliance for connection forwarding is:
A. 7810
B. 7850
C. 7801
D. 7820
Answer: B
Q89. Which of the following is true regarding the CMC appliance?
A. Can be configured using its default IP address of 192.168.1.1
B. Can be initially set up via the CLI
C. Can be initially setup via the AUX interface
D. Can be initially set up via telnet
E. Both C and D
Answer: B
Q90. A customer wants to optimize traffic from remote VPN sites to DMZ servers in the data center shown in the accompanying exhibit.
The customer would also like to deploy their data center Steelhead appliance in a way that would allow them to keep transparency to the LAN servers, and allow the LAN servers to initiate optimized connections to remote sites. The current network architecture can satisfy these requirements by using which following deployment method?
A. In-path
B. Out-of-path
C. WCCP/PBR
D. Hybrid Mode
E. C and D
Answer: D