100% Guarantee of 105 200 free download materials and bundle for Cisco certification for customers, Real Success Guaranteed with Updated ccna 200 105 pdf dumps vce Materials. 100% PASS ICND2 Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) exam Today!

P.S. 100% Guarantee 200-105 bundle are available on Google Drive, GET MORE: https://drive.google.com/open?id=1LPOwiv-vOUqlzBFPqF4sLauwGHst3olw


New Cisco 200-105 Exam Dumps Collection (Question 14 - Question 23)

Q1.

Why has the Branch3 router lost connectivity with R1?

Use only show commands to troubleshoot because usage of the debug command is restricted on the Branch3 and R1 routers.

A. A PPP chap hostname mismatch is noticed between Branch3 and R1.

B. A PPP chap password mismatch is noticed between Branch3 and R1.

C. PPP encapsulation is not configured on Branch3.

D. The PPP chap hostname and PPP chap password commands are missing on the Branch3 router.

Answer: A


Q2. Refer to Exhibit:

The internetwork infrastructure of company XYZ consists of a single OSPF area as shown in the graphic. There is concern that a lack of router resources is impeding internetwork performance. As part of examining the router resources, the OSPF DRs need to be known. All the router OSPF priorities are at the default and the router IDs are shown with each router. Which routers are likely to have been elected as DR? (Choose two.)

A. Corp-1

B. Corp-2

C. Corp-3

D. Corp-4

E. Branch-1

F. Branch-2

Answer: D,F

Explanation: There are 2 segments on the topology above which are separated by Corp-3 router. Each segment will have a DR so we have 2 DRs.

To select which router will become DR they will compare their router-IDs. The router with highest (best) router-ID will become DR. The router-ID is chosen in the order below:

The highest IP address assigned to a loopback (logical) interface.

If a loopback interface is not defined, the highest IP address of all active routeru2021s physical interfaces will be chosen.

In this question, the IP addresses of loopback interfaces are not mentioned so we will consider IP addresses of all active routeru2021s physical interfaces. Router Corp-4 (10.1.40.40)

& Branch-2 (10.2.20.20) have highest u201cactiveu201d IP addresses so they will become DRs.


Q3. Refer to the exhibit.

Why has this switch not been elected the root bridge for VLAN1?

A. It has more than one interface that is connected to the root network segment.

B. It is running RSTP while the elected root bridge is running 802.1d spanning tree.

C. It has a higher MAC address than the elected root bridge.

D. It has a higher bridge ID than the elected root bridge.

Answer: D

Explanation: http://www.cisco.com/en/US/tech/tk389/tk621/technologies_tech_note09186a008009482f.s html

When a switch receives a BPDU, it first compares priority, the lower number wins. If a tie, compare MAC, the smaller one wins. Here Switch has 32769 priority which is greater than 20481 so switch will not elect for root bridge. It says the bridge priority for Switch is 32769, and the root priority is 20481. Which means that some other switch has the lower priority and won the election for VLAN 1.


Q4. Which three responses does TACAS+ give while querying. (Choose three)

A. error

B. accept

C. continue

D. persist

E. fault

Answer: A,B,C


Q5. Routers R1 and R2 are on the same network segment, and both routers use interface Ethernet0/0. If R1 loses communication to R2, which two terns should you check as you begn GigabitEthernetO/0. If R1 lose: troubleshooting? (Choose two )

A. Verify that R2 is using 802 1q encapsulation

B. Verify that the GigabrtEthernet0/0 interfaces on R1 and R2 are configured with the same subnet mask.

C. Verify that the R1 GigabitEthernet0/0 interface is up and the line protocol is down.

D. Verify that R1 and R2 both are using HDLC encapsulation

E. that the R1 GigabitEthernet0/0 interface is up and the line protocol is up.

Answer: B,C


Q6. Refer to the exhibit.

Based on the exhibited routing table, how will packets from a host within the 192.168.10.192/26 LAN be forwarded to 192.168.10.1?

A. The router will forward packets from R3 to R2 to R1.

B. The router will forward packets from R3 to R1 to R2.

C. The router will forward packets from R3 to R2 to R1 AND from R3 to R1.

D. The router will forward packets from R3 to R1.

Answer: C

Explanation:

From the routing table we learn that network 192.168.10.0/30 is learned via 2 equal- cost paths (192.168.10.9 &192.168.10.5) - traffic to this network will be load-balanced.


Q7. Which parameter would you tune to affect the selection of a static route as a backup, when a dynamic protocol is also being used?

A. hop count

B. administrative distance

C. link bandwidth

D. link delay

E. link cost

Answer: B

Explanation:

What Is Administrative Distance? http://www.cisco.com/en/US/tech/tk365/technologies_tech_note09186a0080094195.shtml

Administrative distance is the feature that routers use in order to select the best path. Administrative distance defines the reliability of a routing protocol. Each routing protocol is prioritized in order of most to least reliable (believable) with the help of an administrative distance value. Lowest Administrative distance will be chosen first.


Q8. Which statement describes the process ID that is used to run OSPF on a router?

A. It is globally significant and is used to represent the AS number.

B. It is locally significant and is used to identify an instance of the OSPF database.

C. It is globally significant and is used to identify OSPF stub areas.

D. It is locally significant and must be the same throughout an area.

Answer: B

Explanation: The Process ID for OSPF on a router is only locally significant and you can use the same number on each router, or each router can have a different number-it just

doesn't matter. The numbers you can use are from 1 to 65,535. Don't get this confused with area numbers, which can be from 0 to 4.2 billion.


Q9. What is the default maximum number of equal-cost paths that can be placed into the routing table of a Cisco OSPF router?

A. 2

B. 4

C. 16

D. unlimited

Answer: B

Explanation:

4 is the default number of routes that OSPF will include in routing table if more than 4 equal cost routes exist for the same subnet. However, OSPF can include up to 16 equal cost routes in the routing table and perform load balancing amongst them. In order to configure this feature, you need to use the OSPF subcommand maximum-paths, i.e. maximum- paths 16.


Q10. Which device classes are used over serial links? (Choose two)

A. DCE

B. DTE

C. LCP

D. HDLC

E. PPP

F. LMI

Answer: A,B


Recommend!! Get the 100% Guarantee 200-105 dumps in VCE and PDF From 2passeasy, Welcome to download: https://www.2passeasy.com/dumps/200-105/ (New 267 Q&As Version)