Our authorities create your Cisco Cisco certification online coaching course and also revise the organizing materials along with full devotion. Having help from the Examcollections Cisco exam dumps will allow you to get certified easily. The on the internet Cisco 400-101 study guidebook is superior than the lengthy books for the 400-101 exam preparation. Youll be able to trust your success on our Cisco Cisco exam question and also answers. Just spend a little money and a small span of time about the Cisco 400-101 exam preparation.
2021 Apr 400-101 testing engine
Q401. Refer to the exhibit.
If router R1 is functioning as a DHCPv6 server and you enter the command show ipv6 dhcp binding, which two options are pieces of information in the output? (Choose two.)
A. The IA PD
B. The DUID
C. The prefix pool
D. The DNS server
E. The Rapid-Commit setting
Answer: A,B
Explanation:
In the following example, the show ipv6 dhcp binding command shows information about two clients, including their DUIDs, IAPDs, prefixes, and preferred and valid lifetimes:
Router# show ipv6 dhcp binding
Client: FE80::202:FCFF:FEA5:DC39 (GigabitEthernet2/1/0)
DUID. 000300010002FCA5DC1C
IA PD. IA ID 0x00040001, T1 0, T2 0
Prefix: 3FFE:C00:C18:11::/68
preferred lifetime 180, valid lifetime 12345
expires at Nov 08 2002 02:24 PM (12320 seconds)
Client: FE80::202:FCFF:FEA5:C039 (GigabitEthernet2/1/0)
DUID. 000300010002FCA5C01C
IA PD. IA ID 0x00040001, T1 0, T2 0
Prefix: 3FFE:C00:C18:1::/72
preferred lifetime 240, valid lifetime 54321
expires at Nov 09 2002 02:02 AM (54246 seconds)
Prefix: 3FFE:C00:C18:2::/72
preferred lifetime 300, valid lifetime 54333
expires at Nov 09 2002 02:03 AM (54258 seconds)
Prefix: 3FFE:C00:C18:3::/72
preferred lifetime 280, valid lifetime 51111
Reference: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipaddr_dhcp/configuration/xe-3s/dhcp-xe-3s-book/ip6-dhcp-prefix-xe.html
Q402. How are the Cisco Express Forwarding table and the FIB related to each other?
A. The FIB is used to populate the Cisco Express Forwarding table.
B. The Cisco Express Forwarding table allows route lookups to be forwarded to the route processor for processing before they are
C. There can be only one FIB but multiple Cisco Express Forwarding tables on IOS devices.
D. Cisco Express Forwarding uses a FIB to make IP destination prefix-based switching decisions.
Answer: D
Q403. When BGP route reflectors are used, which attribute ensures that a routing loop is not created?
A. weight
B. local preference
C. multiexit discriminator
D. originator ID
Answer: D
Explanation:
As the iBGP learned routes are reflected, routing information may loop. The route reflector model has the following mechanisms to avoid routing loops:
. Originator ID is an optional, nontransitive BGP attribute. It is a 4-byte attributed created by a route reflector. The attribute carries the router ID of the originator of the route in the local autonomous system. Therefore, if a misconfiguration causes routing information to come back to the originator, the information is ignored.
. Cluster-list is an optional, nontransitive BGP attribute. It is a sequence of cluster IDs that the route has passed. When a route reflector reflects a route from its clients to nonclient peers, and vice versa, it appends the local cluster ID to the cluster-list. If the cluster-list is empty, a new cluster-list is created. Using this attribute, a route reflector can identify if routing information is looped back to the same cluster due to misconfiguration. If the local cluster ID is found in the cluster-list, the advertisement is ignored.
Reference: http://www.cisco.com/c/en/us/td/docs/ios/12_2/ip/configuration/guide/fipr_c/1cfbgp.html
Q404. Refer to the exhibit.
Which statement about the route target for 192.168.1.0/24 is true?
A. Its route target is 64512:100010051.
B. Its route targets are 64512:100010051, 64512:2002250, and 64512:3002300.
C. Its route target is 64512:3002300.
D. Its route targets are 64512:100010051 and 64512:3002300.
E. Its route targets are 64512:2002250 and 64512:3002300.
Answer: C
Explanation:
Here we are using route maps to change the route target for the 192.168.1.0/24 network from the default route target of 64512:100010051 to 64512:3002300.
Q405. When you migrate a network from PVST+ to rapid-PVST+, which two features become inactive? (Choose two.)
A. Root guard
B. Loop guard
C. UplinkFast
D. UDLD
E. BackboneFast
F. Bridge Assurance
Answer: C,E
Explanation:
It is good to know the UplinkFast and BackboneFast behavior before you start the migration process.
Here, the Access1 switch runs Cisco IOS. This output is taken before migration to the rapid-PVST+ mode:
Access1#show spanning-tree vlan 10
VLAN0010
Spanning tree enabled protocol ieee
Root ID Priority 24586
Address 0015.63f6.b700
Cost 3019
Port 107 (FastEthernet3/0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 49162 (priority 49152 sys-id-ext 10)
Address 000f.f794.3d00
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Uplinkfast enabled
Interface Role Sts Cost Prio.Nbr Type
Fa3/0/1 Root FWD 3019 128.107 P2p
Fa3/0/2 Altn BLK 3019 128.108 P2p
Access1#show spanning-tree summary
Switch is in pvst mode
Root bridge for: none
Extended system ID is enabled
Portfast Default is disabled
PortFast BPDU Guard Default is enabled
Portfast BPDU Filter Default is disabled
Loopguard Default is disabled
EtherChannel misconfig guard is enabled
UplinkFast is enabled
BackboneFast is enabled
Configured Pathcost method used is short
Name Blocking Listening Learning Forwarding STP Active
VLAN0010 1 0 0 1 2
VLAN0020 1 0 0 1 2
2 vlans 2 0 0 2 4
This output is taken after the mode is changed to rapid-PVST+:
Access1#show spanning-tree vlan 10
VLAN0010
Spanning tree enabled protocol rstp
Root ID Priority 24586
Address 0015.63f6.b700
Cost 3019
Port 107 (FastEthernet3/0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 49162 (priority 49152 sys-id-ext 10)
Address 000f.f794.3d00
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
UplinkFast enabled but inactive in rapid-pvst mode
Interface Role Sts Cost Prio.Nbr Type
Fa3/0/1 Root FWD 3019 128.107 P2p
Fa3/0/2 Altn BLK 3019 128.108 P2p
Access1#show spanning-tree summary
Switch is in rapid-pvst mode
Root bridge for: none
Extended system ID is enabled
Portfast Default is disabled
PortFast BPDU Guard Default is enabled
Portfast BPDU Filter Default is disabled
Loopguard Default is disabled
EtherChannel misconfig guard is enabled
UplinkFast is enabled but inactive in rapid-pvst mode
BackboneFast is enabled but inactive in rapid-pvst mode
Configured Pathcost method used is short
Name Blocking Listening Learning Forwarding STP Active
VLAN0010 1 0 0 1 2
VLAN0020 1 0 0 1 2
2 vlans 2 0 0 2 4
You can see in the show spanning-tree summary command output that UplinkFast and BackboneFast are enabled, but are inactive in rapid-PVST mode.
Reference: http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/72836-rapidpvst-mig-config.html#upback1
Replace 400-101 real exam:
Q406. Which two statements about VRRP are true? (Choose two.)
A. It is assigned multicast address 224.0.0.18.
B. The TTL for VRRP packets must be 255.
C. It is assigned multicast address 224.0.0.9.
D. Its IP protocol number is 115.
E. Three versions of the VRRP protocol have been defined.
F. It supports both MD5 and SHA1 authentication.
Answer: A,B
Q407. DRAG DROP
Answer:
Q408. DRAG DROP
Drag and drop the EIGRP term on the left to the corresponding definition on the right.
Answer:
Q409. Which three statements about EVCs are true? (Choose three.)
A. Spanning Tree must use MST mode on EVC ports.
B. PAGP is supported on EVC ports.
C. Spanning Tree must use RSTP mode on EVC ports.
D. LACP is supported on EVC ports.
E. Layer 2 multicast framing is supported.
F. Bridge domain routing is required.
Answer: A,B,D
Explanation:
EVC support requires the following:
–The spanning tree mode must be MST.
–The dot1ad global configuration mode command must be configured.
These Layer 2 port-based features can run with EVC configured on a port:
–PAGP
–LACP
–UDLD
–LLDP
–CDP
–MSTP
Reference: http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/ios/12-2SY/configuration/guide/sy_swcg/ethernet_virtual_connection.html
Q410. In a PfR environment, which two statements best describe the difference between active mode monitoring and fast mode monitoring? (Choose two.)
A. Active mode monitoring can monitor and measure actual traffic via NetFlow data collection.
B. Fast mode monitoring can measure bursty traffic better than active mode.
C. Active mode monitoring uses IP SLA probes for the purpose of obtaining performance characteristics of the current WAN exit link.
D. Fast mode monitoring uses IP SLA probes via all valid exits continuously to quickly determine an alternate exit link.
Answer: C,D
Explanation:
Active Monitoring
PfR uses Cisco IOS IP Service Level Agreements (SLAs) to enable active monitoring. IP SLAs support is enabled by default. IP SLAs support allows PfR to be configured to send active probes to target IP addresses to measure the jitter and delay, determining if a prefix is out-of-policy and if the best exit is selected. The border router collects these performance statistics from the active probe and transmits this information to the master controller.
Fast Failover Monitoring
Fast failover monitoring enables passive and active monitoring and sets the active probes to continuously monitor all the exits (probe-all). Fast failover monitoring can be used with all types of active probes: Internet Control Message Protocol (ICMP) echo, jitter, TCP connection, and UDP echo.
Reference: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/pfr/command/pfr-cr-book/pfr-s1.html