It is more faster and easier to pass the Cisco 300-365 exam by using Vivid Cisco Deploying Cisco Wireless Enterprise Networks questuins and answers. Immediate access to the Up to the minute 300-365 Exam and find the same core area 300-365 questions with professionally verified answers, then PASS your exam with a high score now.
Q11. What address do PIM routers listen to in order to automatically discover the best RP for each multicast group?
A. 224.0.0.13
B. 224.0.1.39
C. 224.0.0.14
D. 224.0.140
Answer: D
Q12. Which show command will show whether a WLAN is locally or centrally switched on a Cisco Wireless Lan Controller?
A. show ap config general Cisco_AP
B. show wlan wlan_id
C. show flexconnect summary
D. show flexconnect group detail
Answer: B
Q13. A customer requires that the remote site be able to utilize local servers when the AP is in WAN-down (standalone mode). Which AP mode must be configured on the wireless controller?
A. SE-Connect
B. Monitor
C. Local
D. FlexConnect
E. Sniffer
F. Rogue Detector
Answer: D
Q14. An engineer wants to configure Call Admission Control and ensure that AC is based on the capacity of the AP and considering the possible impact of other APs in the area. Which two configuration options are required? (Choose two.)
A. StaticCAC
B. Admission Control
C. Load-Based AC
D. Add Traffic Stream
E. Reserved Roaming Bandwidth
F. Expedited Bandwidth
Answer: B,C
Q15. What devices can be tracked with the Cisco Context Aware Services?
A. Only wired devices.
B. Both wired and wireless devices.
C. Only Cisco certified wireless devices.
D. Only wireless devices.
Answer: B
Q16. After a wireless deployment, users report that wireless voice clients are experiencing an unacceptable amount of delay while roaming during a call on the Cisco Unified 7925 Series phones. The customer environment consists of multiple controllers, all running 7.4.121.0 code, operating in a centralized deployment. What configuration issue is most likely contributing to the problem?
A. The authentication should be set to WPA2-PSK to allow for 802.11n speeds for the Cisco Unified 7925 phones.
B. The access points on that floor are all on one controller and should be load balanced evenly across multiple controllers.
C. The access points for that floor are salt and peppered across multiple controllers and should be moved to the primary controller.
D. The wireless phones are operating in the 2 4 GHz band and should be configured for the 5 GHz band.
Answer: B
Q17. A customer requires wireless traffic from the branch to be routed through the firewall at corporate headquarters. There is a RADIUS server in each branch location. Which FlexConnect state should be used in this scenario?
A. local authentication and local switching
B. local authentication and central switching
C. central authentication and central switching
D. central authentication and local switching
Answer: C
Q18. A network engineer is experiencing issues enabling LAG on the WLC. Which four characteristics should be validated to ensure LAG configuration? (Choose four.)
A. All ports participate in the LAG by default when LAG is enabled on the controller, y
B. Dynamic interfaces and management are moved to port 1
C. Primary and secondary ports are needed for each interface.
D. Multiple untagged interfaces to the same port are not allowed.
E. EtherChannel must be configured for mode "on" on the switch.
F. Only one functional physical port is needed to continue to pass traffic.
G. Multiple LAGs are permitted on the controller.
H. The WLC does not need to be rebooted to enable the LAG configuration.
Answer: A,D,E,F
Q19. A customer is implementing a massively scaled guest wireless network to support approximately 32,000 clients. For ease of administration, they have required implementing multiple interfaces defined on the WLC and mapped to a single interface group. Which configuration meets this need?
A. 264 interfaces of/25 sized networks
B. 132 interfaces of/24 sized networks
C. 66 interfaces of/23 sized networks
D. 33 interfaces of /22 sized networks
Answer: D
Q20. RAG DROP
Drag the QoS values from the left and drop them in the correct descending order of priority on the right.
Answer: