It is more faster and easier to pass the Cisco cisco 100 105 pdf exam by using Download Cisco Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) questuins and answers. Immediate access to the Improved ccent 100 105 pdf Exam and find the same core area 100 105 icnd1 pdf questions with professionally verified answers, then PASS your exam with a high score now.
Q71. CORRECT TEXT - (Topic 6)
There are three locations in a school district of a large city: ROUTER -M, ROUTER -W and ROUTER -U. The network connection between two of these locations has already functioned. Configure the ROUTER -M router IP addresses on the E0 and S0 interfaces so that the E0 receives the first usable subnet while the S0 receives the second usable subnet from the network 192.168.160.0/28. Both interfaces would receive the last available ip address on the proper subnet.
NotE. The OSPF process must be configured to allow interfaces in specific subnets to participate in the routing process.
Answer: ROUTER-M> enable PassworD. Cisco ROUTER-M# config t ROUTER-M(config)# interface e0 ROUTER-M(config-if)# ip address 192.168.160.14 255.255.255.240
ROUTER-M(config-if)# no shutdown ROUTER -M(config-if)# exit ROUTER -M(config)# interface s0 ROUTER-M(config-if)# ip address 192.168.160.30 255.255.255.240 ROUTER-M(config-if)# no shutdown ROUTER-M(config-if)# end ROUTER-M# copy run start
Q72. - (Topic 5)
Refer to the exhibit.
A problem with network connectivity has been observed. It is suspected that the cable connected to switch port Fa0/9 on Switch1 is disconnected. What would be an effect of this cable being disconnected?
A. Host B would not be able to access the server in VLAN9 until the cable is reconnected.
B. Communication between VLAN3 and the other VLANs would be disabled.
C. The transfer of files from Host B to the server in VLAN9 would be significantly slower.
D. For less than a minute, Host B would not be able to access the server in VLAN9. Then normal network function would resume.
Answer: D
Explanation:
Because Switch1 has multiple redundant links in this network, traffic would not work for less than a minute, and then it would get rerouted along the longer path to the host. The 1 minute outage would be the length of time it takes STP to converge.
Q73. - (Topic 3)
What is the default administrative distance of the OSPF routing protocol?
A. 90
B. 100
C. 110
D. 120
E. 130
F. 170
Answer: C
Explanation:
Default Distance Value Table This table lists the administrative distance default values of the protocols that Cisco supports: If the administrative distance is 255, the router does not believe the source of that route and does not install the route in the routing table.
Q74. - (Topic 2)
Refer to the exhibit.
How many collision domains are shown?
A. one
B. two
C. three
D. four
E. six
F. twelve
Answer: B
Explanation:
Hubs create single collision and broadcast domains, so in this case there will be a single collision domain for each of the two hubs.
Q75. - (Topic 5)
Refer to the exhibit.
A TFTP server has recently been installed in the Atlanta office. The network administrator is located in the NY office and has made a console connection to the NY router. After establishing the connection they are unable to backup the configuration file and IOS of the NY router to the TFTP server. What is the cause of this problem?
A. The NY router has an incorrect subnet mask.
B. The TFTP server has an incorrect IP address.
C. The TFTP server has an incorrect subnet mask.
D. The network administrator computer has an incorrect IP address.
Answer: C
Explanation:
The TFTP server is using a mask of 255.255.255.240 (/28) while the router is configured with a /29. Because of this, the Atlanta router does not see the TFTP server as being in the same subnet.
Q76. - (Topic 3)
Refer to the exhibit.
The two routers have had their startup configurations cleared and have been restarted. At a minimum, what must the administrator do to enable CDP to exchange information between R1 and R2?
A. Configure the router with the cdp enable command.
B. Enter no shutdown commands on the R1 and R2 fa0/1 interfaces.
C. Configure IP addressing and no shutdown commands on both the R1 and R2 fa0/1 interfaces.
D. Configure IP addressing and no shutdown commands on either of the R1 or R2 fa0/1 interfaces.
Answer: B
Explanation:
If the no shut down commands are not entered, then CDP can exchange information between the two routers. By default, all Cisco device interfaces and ports are shut down and need to be manually enabled.
Q77. - (Topic 3)
Scenario
Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links.
You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices.
An OSPF neighbor adjacency is not formed between R3 in the main office and R5 in the Branch2 office. What is causing the problem?
A. There is an area ID mismatch.
B. There is a PPP authentication issue; a password mismatch.
C. There is an OSPF hello and dead interval mismatch.
D. There is a missing network command in the OSPF process on R5.
Answer: C
Explanation:
The “show ip ospf interface command on R3 and R5 shows that the hello and dead intervals do not match. They are 50 and 200 on R3 and 10 and 40 on R5.
Topic 4, Infrastructure Services
Q78. - (Topic 1)
Which two characteristics describe the access layer of the hierarchical network design model? (Choose two.)
A. layer 3 support
B. port security
C. redundant components
D. VLANs
E. PoE
Answer: B,D
Explanation:
Access layer The main purpose of the access layer is to provide direct connection to devices on the network and controlling which devices are allowed to communicate over it. The access layer interfaces with end devices, such as PCs, printers, and IP phones, to provide access to the rest of the network. The access layer can include routers, switches, bridges, hubs, and wireless access points (AP).
Switch features in the Access layer:
......
Port security
VLANs
Fast Ethernet/Gigabit Ethernet
Power over Ethernet (PoE)
Link aggregation
Quality of Service (QoS)
References: http://www.ciscopath.com/content/61/ http://www.mcmcse.com/cisco/guides/hierarchical_model.shtml
Topic 2, LAN Switching Technologies
Q79. - (Topic 3)
What is the network address for the host with IP address 192.168.23.61/28?
A. 192.168.23.0
B. 192.168.23.32
C. 192.168.23.48
D. 192.168.23.56
E. 192.168.23.60
Answer: C
Explanation:
Convert bit-length prefix to quad-dotted decimal representation, then from it find the number of bits used for subnetting you can find previously calculated number of subnets by separating subnets each having value of last bit used for subnet masking Find that your IP address is in which subnet, that subnet's first address is network address and last address is broadcast address. Based on above steps the answer is option C
Q80. - (Topic 3)
What information can be used by a router running a link-state protocol to build and maintain its topological database? (Choose two.)
A. hello packets
B. SAP messages sent by other routers
C. LSAs from other routers
D. beacons received on point-to-point links
E. routing tables received from other link-state routers
F. TTL packets from designated routers
Answer: A,C
Explanation:
Reference 1: http://www.ciscopress.com/articles/article.asp?p=24090&seqNum=4
Link state protocols, sometimes called shortest path first or distributed database protocols, are built around a well-known algorithm from graph theory, E. W. Dijkstra'a shortest path algorithm. Examples of link state routing protocols are: Open Shortest Path First (OSPF) for IP The ISO's Intermediate System to Intermediate System (IS-IS) for CLNS and IP DEC's DNA Phase V Novell's NetWare Link Services Protocol (NLSP) Although link state protocols are rightly considered more complex than distance vector protocols, the basic functionality is not complex at all:
1.
Each router establishes a relationship—an adjacency—with each of its neighbors.
2.
Each router sends link state advertisements (LSAs), some
3.
Each router stores a copy of all the LSAs it has seen in a database. If all works well, the databases in all routers should be identical.
4.
The completed topological database, also called the link state database, describes a graph of the internetwork. Using the Dijkstra algorithm, each router calculates the shortest path to each network and enters this information into the route table. OSPF Tutorial